fosinator

thanks Phil, turned them around and did the trick.I always thought the long leg(+) would receive from lower number pins so there you go.

Hi thanks for the reply, using Race Coordinator and laptimer2000.Ok will try what you suggested tonite.I thought the long leg went to number 10,11,12,13.Thats what seems strange, the pit sensors work wired that way.Ill double check tonite before too many beers.Thanks

Hi all, wondering if anyone has any ideas on this problem. I got my pit lanes registering but not the lap sensors. 2 lane track with pits zd1950 sensors with matching tx the laps count with a normal switch and when touching wires together just not the sensors. all of the ir tx trigger the pit sensor, so they all work im using a db25 with pins 10,11,12,13 resistors are on the negative leg of the sensor, would not seem work the other way I will try tonight swapping sensors to see if theyre buggered, but I doubt it, theyre new.Seems strange that 2 would be buggered both on the lap count lanes.

ozquad44, yea i got inox now every thing is sweet best fun ive had in a long time.I was gonna wait for the new one but then wasnt sure if it would be delayed so i decided on a c7030 and got PBPro/SH mod done by MIH.By the time i had funds to get the mods done the new PB was out and it would have been cheaper but im still really stoked with the final product.I copper taped cos my track is second hand and the rails seemed pretty bad.Its only a small track but great fun.Ill post in the new tracks shortly.

i dont have any mates now that ive gone to digital:) Na i can seriously see the potential in ssd.I need to adapt as i have gone back to scaley sport track i really miss the routed but the routed digital didnt work like i wanted so i got back into scaley sport.I got 2 clc & 2 xlc plus a couple of hairpins.All up the track must be about 14 metres long.I started copper taping it last night hopefully finish tonite.

Hi i just got my PBPro/SH set up.This is awesome however i was wondering if there is an easy way to set pace cars. Last night i successfully had 2 pace cars on there own ID at separate speeds while i was racing,but i found that to get them going i have to plug into each ID run the car then pull out the control while at speed.I thought I read in the manual that if pace is enabled on an ID when the control is unplugged it would run but they dont unless i "run start "them. Just hoping I could put the cars on the track and they go without plugging in and running them. Is there an easy way?

My mate found a go kart in a hobby store a while back(lucky bugger).I know there not super strong but i just want 1 or even 2.I havent seen them anywhere online.If anyone knows where i can source a couple let me know. Cheers.

Well i decided to replace my slotted in plastic lane changers with wood as i didnt like the metal rails or the thin slots.Should have done this in the first place.Sorry crappy iphone pics. I extended the pin that goes into the flipper as the solenoids will be sitting lower routed out so the sensor board sits flush Hot glued the solenoids on Hot glued a pin on for the flipper to pivot power for the flipper screw into place ready for a touch up with the ferrodor All good practice.Ive decided that if the digital is as good as everyone says,which im hoping, Ill build another track but just two lane digital and pitpro.

yea a couple of weeks ago i had a few nights of dreaming about Lane Changes, couldnt get them out of my damn head,I was building at the time.Amazing how the lane changes would work their way into a dream:)

Kenny, Some 1 lane sections would be awesome .My mind goes into overdrive thinking about track designs.I love blank mdf,a pencil and a rubber. John, I wish i had fiddled with plastic digital before jumping in but like i say i got the bits now, hopefully ill have no regrets.Worst case scenario is ill build another track and thats not a bad thing.I chipped a decent car last night so when th PB comes back ill see how it runs.

Love the action with 3 lane analogue racing but i have to say im getting doubts on the digital.Im sending the powerbase off tomorow for PBPro and simple H mods.I hooked up the digital just to see it all working but i ve only got a crappy digital car going so that stopped a lot of the wow factor.I think this track will end up being "The Digital Test Track to See If It Worked".The important thing is ive got all the digital bits to build another one where i would plan the lane changes a lot more carefully,and also just mount the sensor and flipper,and not the piece of track.But I'll see what happens when the powerbase comes back and ive got some decent chipped cars running.

looking really good squeeze

yea awesome alright .He loves my 1.32 stuff,cant get enough of it,the other 3 kids not that keen.

Started some scenery last night.Some mates coming tonight for a race session should be good. the 'dip'

My youngest is 3 today im just about to put together his micro scaley set.Hopefully be a bit of fun for him.