22 replies to this topic

[lenny broke]

Howdy men
Please post your rally car's specifications here
Include car number, make and model, motor spec., gear ratio, wheels & tyres, guide flag used, weight, any modifications done and any thing else you may feel is relevant to your car.
Thanks, Alan

Edited by lenny broke, 13 November 2009 - 08:29 AM.

[Davnic74]

Fly Racing Porsche 911 # 21.
NC -1 with modified adaptor.
Std Fly Racing Pod with spring upgrade (stiffer).
Std Guide.
Std rims.
MJK rears, std fronts.
Lexan interior.
Weight around 80 gms, Blutak placed in precisly measured places for ultimate car balance..
Ninco Lead wire.
Body lowered 1mm all around.

Edited by Davnic74, 13 November 2009 - 07:12 PM.

[Yngwie]

SCX BMW M3
NC-2 Motor (oops)
Std Front rims and tyres
Slot.it Rear Axle assembly
Slot.it P6's on rears
Ninco guide.
Ninco lead wire.
Weight around 100gms

Regards
John

[Obsidith]

Ford Escort RS Cosworth Pilot rally number 14
SCX RX-81 with gold dust brushes
SCX Pro Axles
SCX Pro Alloy Rims 17" with the inside of the hubs machined down to make the wheels fit under
SCX Pro Gear 9/27 front and rear
Tyres front where SCX DTM tryes that where cut down
rear BRM 22 shore
Chassis was trimmed to make it float and to raise the ride hight
Lead added and glued in
oiled and posted off

so i really didnt do much as i have no idea what i was doing then i know alot me now

[Ronan]

Ninco Porsche 911 SC Martini (number 9)

Sloting Plus 18000 rally motor

slot.it inline rear axle kit and wheels

slot.it indepenent rotation front axle with MB Slot wheels

weight around 90g or so (can't remember exactly!)

Ortmann rear tyres

Can't remember the gear ratio, but nothing too unusual (9/27 I think?)

Kept the Ninco sprung guide that came on the car, no chassis mods other than loosening the screws

[Ben_M]

#2 SCX Celica
SCX Rx-8 motor (4x4)
9/24 slot it gears
slot it axle kit & wheels
mjk tyres all round
ninco pro sprung guide
total weight about 100g

[Antony]

Ninco Austin Healey 3000
NC2 in fashionable black
Slot it axles, bearings and gears 9/25 or 9/24 can't remember which but being Slot it the colour will give it away!
BWA wheels and inserts
Ortmann rear tyres, Ninco fronts
Ninco Sprung Guide as fitted
Lead sheet applied inside.

Edited by Antony, 13 November 2009 - 11:34 AM.

[brk12345]

BRK12345, car no 27, SCX Toyota Celica GT4, Ninco NC1 motor, Fly alloy wheels, MJK rear tyres, Ninco fronts, Ninco sprung guide. Car runs 9/26 gearing and weights a touch over 100g.

[oldslot]

spirit peugeot 205 t-16 slot-it boxer motor mjk rears whatever gearing it came with, about 100 g. weight

[espsix]

SCX Audi Quatro, NC-8 motor, SlotIt F25 tyres, Ninco sprung guide, stock wheels, stock interior with co driver added, body lowered at the front by 1mm, not sure of weight.

[suttle]

Spirit Peugeot T16 Inline rear wheel drive Original motor approx 23,000RPM Slotit9/27 gearing NSR wheels and axles Original bearings Ninco pro race guide fixed to original drop arm no spring NSR rear tyres Ninco front Small amount of lead added to each pan on chassis Loose body.

[munter]

SCX Abarth 124 which I bought cheap from a local caryard.
The most work was in the rear end with a slotit install and mjk tires,the motor had a few tweaks and some weight was added.(not much)
Oh and some chassis bracing was done too...

[haystack]

Haystackmobile2 (hereinafter referred to as the Stackmobile) is an SCX Renault R5, #15 in White/black/brown livery circa'84

Fly Rally 1(allsame black NC-2), Slot-it gearset/axle rear 9/27?, Alloys, 40 shore urethanes (Phil), soldered leadwires....no, they don't count

as metal bracing , std wheels & tyres front, vac form interior, and lollypop tube keeper for contrate, at @ 91gms.

Wish me luck, and you'll deserve yours

[gazza]

Fly 911
Yellow strip down the centre
MJK's and a Ninco guide
Everything else standard

[John Schoen]

Team Slot Renault Alpine A110 #22
Black NC-2
Slot.it pinion and crown gear, 10/28
Scaleauto guide
Slot.it zero grips 19 x 10 front
PKS SL008B 18,5 x 10,5 rear
NSR bushings
Sloting Plus axles
Sloting Plus America wheels

[Ontheflipside]

The Audi Quattro never got off the ground due to time restraints so had to go with . . .

A Red Ninco Porsche 911 Racing #5
NC-1 Motor
MJK rear tyres
Weighted to 86 grams
Rear bearings glued in to stop the "hop" and front bearings glued in to comply with ground clearance rules

Everything else standard

Painted the bonnet and turret matt black after stuffing up a white paint mod.
Added the Boxing Kangaroo as it has been good luck for me with two cars in the current SCX Rally

If I could download pics off my mobile I would add a pic, but looks similar to:

Edited by Ontheflipside, 13 November 2009 - 10:01 PM.

[kalbfellp]

Better add mine as I instigated this!
SCX Subaru repsol. Vac formed windows and interior, NC2 (black) Slot It gears and axle(9/28 or 9/27) BWA rear wheels. Tassie Resin Rear tyres,fronts NSR low grip, Ninco sprung guide. Weight is about 100 grams I think.

[smallnails]

FLY Racing 911

Carefully placed weight, NC2 and MJK's, fly racing lo grip guide

all else standard, so i really am expecting to have to replace the fly racing gear at some stage!

[munter]

Quote

fly racing lo grip guide

Please tell me more Smallnails...what are they exactly?

regards

[haystack]

munter, on Nov 14 2009, 10:04 AM, said:

Quote

fly racing lo grip guide

Please tell me more Smallnails...what are they exactly?

regards

If you check out the picture of Davnics Porsche at the top of this thread, you will see one.....Red...they are some Teflon/nylon hybrid low friction material, and come std on Fly Racing series cars