Jump to content
lenny broke

2021 Tasman Cup Proxy Race Series Spec Sheet

Recommended Posts

Hi Guys'

Here's a Spec Sheet for all the cars in this years series. Please post or PM your car specifications and I will update the sheet on a regular basis.

Cheers, Alan

tasman-2021-Spec-sheet-07-Mar21.jpg

 

Edited by lenny broke
updated 07Mar21

Share this post


Link to post
Share on other sites

Sharknose Ferrari Scalextric  Samson Classic (DSC)             Slotting plus MrSlotCar Pinion  Slot It gear Paul Gage tires,  RSslot f/r wheels

 

Edited by Brumos RSR

Share this post


Link to post
Share on other sites

Hi Lenny/Alan.

My Brabham BT3 will much the same as last 3 years or so but will be fitted with new SRP16000 FF050 motor and new PG rear tyres. I hope to also re-build the front axle mount so it will be eligible for FPR building competition. Hopefully also tidy up Stubbo's original  paint job.

Spec. details are as follows: 1963 Brabham BT3 driven by the late Denny Hulme (No. 5); entry country - New Zealand; body STUBBO including paint job as far as I know; chassis Le Breton with BWA motor mount; motor SRP16000; guide - Slot-it; pinion BWA; crown wheel - Slot-it; gear ration - TBD; rear tyres PG21083; wheels - F&R - BWA; 

Regards Chas Le Breton

 

Edited by charlesx

Share this post


Link to post
Share on other sites

Peter Gunn no 14 Lotus 24 B.R.M P/P body  Beardog chassis , Tassie 1790 motor, MRRC guide, Slot it pinion, Slot it crown wheel, gear ratio 9x24, rear tyres Yellowdog compound, Rear wheels RS, Front wheels RS.

 

Dixie no 16 Lotus 24 B.R.M P/P body, Beardog chassis , SRP 18 K Motor, MRRC guide, Slot it pinion, Slot it crown wheel, gear ratio 10x 24, rear tyres Yellowdog compound, Rear wheels RS, Front wheels RS.

 

 

Share this post


Link to post
Share on other sites

Hi Lenny,

 

Here are the details of the Gippsland Cars

 

CAR Entrant Car Body Chassis MOTOR Guide Pinion Gear Gear Tyre Wheels Wheels
#     Make     Make   Make Ratio Make front rear
                    Rear    
2 Stubbo Brabham Climax SBW Stubbo Tasman 1790 NSR Scalex Slot It 9:24 Gage BWA BWA
41 Plugger Brabham Climax SBW Slo1quick Tasman 1790 NSR Scalex Slot It 9:24 Gage BWA BWA
66 Sainter Brabham Climax SBW Slo1quick SRP 18 NSR BWA Slot It 9:23 Gage BWA BWA

Alan Stubbings

Share this post


Link to post
Share on other sites

Hi Lenny and all.

The Bruce and Denny show is finally on the road to AUS. Details for both cars are as follows:

Please note there are a few minor changes to Brabham BT3.

Brabham

 

·         Name:  Charles Le Breton, charlesx, ID. CX1 on bottom of car.

·         Contact details: charlesx@xtra.co.nz, 0276400504NZ

·         Number Preference(s) No.3 as allotted.

·         Car Details  BWA wheels, Dart front tyres and PG21083 rear tyres, MRRC pinion and NSR contrate. Gear ratio 10:24, SRP18000 motor. Total weight 57.10gms.

·         Car make and model  1963 Brabham BT3 as raced at Pukekohe by Denny Hulme in Tasman Cup.

·         Body Manufacturer - Stubbo including paint job. Sorry Stubbo car is a little knocked around after several years on road.

·         Chassis type and manufacturer name Self made with BWA engine mount and piano wire rails, brass rod for steering, suspension arms, springs, exhaust from engine then a brass tube exhaust pipe, black coated plastic wire for hydraulic hoses. Separately rotating front wheels with brass tube axle, Thunderslot guide, decals paint and engine detail by me

Cooper Climax

 

·         Name: Charles Le Breton, charlesx, ID. CX2 on bottom of car.

·         Contact details: charlesx@xtra.co.nz, 0276400504NZ

·         Number Preference(s) No 5 as originally allotted to my Brabham. 

·         Car Details - Self made with BWA engine mount and brass rod rails, brass rod for steering, suspension and springs. Brass tube for exhausts. BWA pinion, Slot-it contrate, gear ratio 9:23, BWA 14000 motor. Total weight 56.85gms.

·         Car make and model 1962 T60 Copper-Climax as raced by Bruce McLaren in Tasman Cup.

·         Body Manufacturer 6-7 years ago I think by Phil from Tasmania. Preparation, paint and decals by me.

·         Chassis type and manufacturer name - Self made with BWA engine mount and brass rod rails, suspension and springs. brass tube exhausts and front axle tube. Slot-it guide plus decals paint and engine detail by me.

Please advise if I have missed anything. Sorry cannot add photos so am sending to Lenny. Cars sent today.

Regards Chas Le Breton (charlesx)

 

 

Edited by charlesx
Add weight of cars.

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...