Jump to content
Caddo

Endbell Drive Sidewinder Motor Pods

Recommended Posts

G'day

 

Any one know of a source for Mabuchi motor, end bell drive sidewinder pods, similar to the old Slot It classic car pods? They are all can drive pods now.

 

3D printed is ok.

 

Cheers Caddo

Share this post


Link to post
Share on other sites

hi Caddo,

 

What a coincidence!

 

I've been trying to find the same thing ... see my posts in the 'New Products' thread.

 

The ones I thought I'd found were made by Devis 3D Designs but are now out of production AFAIK.

 

LEB Hobbies website lists them but the illustrations of 'endbell drive pods' don't have the large D-shaped mounting hole where the endbell of an S-Can would snap in.

 

If you have any Fly cars that are sidewinders with pods you'll see what I mean ... the endbell of the motor (and the large D-shaped mounting) is near the left hand rear wheel.

 

I would be happy to buy some from the US if I be sure I was getting the right thing.

 

Den

Share this post


Link to post
Share on other sites

You're right Caddo.

 

BUT ... I am still having discussions with LEB regarding the pictures of the Devis S-can pods.

I'm hoping that it's just the pictures on the website that are incorrect and that there really are end-bell drive pods available.

 

The point I've made to LEB and have mentioned in the other thread, is that Fly, SRC, Scalextric etc end-bell drive cars all have the larger D-shaped mounting hole closest to the left-hand rear wheel ... obviously because that's where the end-bell is positioned.

 

I'll keep you posted on any feedback that I get.

 

Den

Share this post


Link to post
Share on other sites

Great! thank you very much! Hoping there is an option there.

Slot It aren't interested in producing any of their old end bell drive sidewinder pods

Share this post


Link to post
Share on other sites

Not wishing to open the floodgates on Pandora's tin of worms, but why the preference for endbell drive pods?

Share this post


Link to post
Share on other sites

G'day Alan

 

Not sure what Caddo's motivation is but for me it's just about building 'fun cars' without having to spend big money on motors e.g I can buy a Scalextric S-Can (endbell drive) for less then half the price of (for example) a Slot.It double-shaft motor.

 

Think back to the Jag Challenge in NZ where the object was to recycle 30-year-old Scalextric cars.

 

I also buy quite a bit of S/H stuff and quite often the motors and the rear axle assemblies are OK even though other components might be beyond salvage.

 

And harking back to Munter's thread about cost versus fun, one of the cars I ran at Phil's last Tuesday was a Scalextric Escort Mk 1 rally car with two lady drivers. Because the original rear wheels were so far out of line I was actually running 50-y-o Formula Junior wheels on the car.

 

Boss302 was quick to notice ... maybe because it was so slow!

 

Den

Share this post


Link to post
Share on other sites

I'm converting my Scaley cars to 3D printed chassis with sidewinder pods, and want to keep the original Scaley motors.

All the Scaley motors I have are end bell drive with a single shaft.

I'm looking for end bell drive pods top suit the motors.

Share this post


Link to post
Share on other sites

Thanks chaps

I wasn't thinking in terms of Scalex motors going in, makes sense

cheers

 

Alan

Edited by lenny broke

Share this post


Link to post
Share on other sites

Thanks for your continuing interest in this topic Alan.

 

When it comes to cars that are unlikely to be competitive I'm not a believer in the concept of 'shelf queens'.

 

So I'm happy to build and run a few 'track queens' but I don't want to spend a fortune in doing so.

 

I'm also interested in the FF 3D motor pods also because the cost of building a 'track queen' can be reduced even further by using the very cheap FF motors.

 

Den

Share this post


Link to post
Share on other sites

I hear ya Den,

I have a collection of SCX RX42 motors that I've swapped out for something quicker over the years that I'd like to use. I also have quite a few resin bodies that aren't suitable for club racing, so I'm aiming to scratch build some chassis' and use those motors to power them.

Cheers,

Alan

Share this post


Link to post
Share on other sites

With the 3d chassis revolution, it's a bit short sighted of Slot It not to produce the end bell drive pods IMO

  • Upvote 1

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...