Jump to content
Sign in to follow this  
gregc4

2017 Mcn 1/32 Class Rules

Recommended Posts

LMP/GT1 PROTO Open Rules:

 

NOTE :EVEN THOUGH IT IS AN OPEN CLASS THE CAR MUST STILL LOOK LIKE A RTR 1/32 SCALE CAR .

AXLES FRONT

1.Must be located in original,un-modified front axel holders.

2.Stabelizing of front end is allowed.

3.wheels must be inside the guards.

AXLES REAR

1.Must be located in original un-modified rear axel holders.

2.Ball bearings are allowed.

3.wheels must be inside the guards.

BODY:

1.NO sanding of wheel arches to allow for room for tyres to fit.

2.The body can NOT be modified in any way.Exception on the Nissan R90 where the gear hits on the air duct

3.Any screws can be used.

4.Any body that has a wing can have rubber added as struts to stop the wing from braking off.

5.Painted liveries are allowed making sure all parts are used. Race numbers in at least 3 places.

CHASSIS:

1.Adding weight to any part of the chassis is allowed.

2.Reinforcing or gluing parts of the chassis such as axel bushings,motor mounting posts etc is allowed.

3. NO chassis magnets are allowed.

4. Must be plastic RTR plastic chassis to suit the body.After market plastic Chassis that are made to suit the body are allowed. No metal chassis.

GEARS:

1. OPEN Gear Ratio.

GROUND CLEARANCE:

1. As long as day light can be seen.

GUIDE:

1.Any Guide.

2.Any lead wire.

3.Any Braid.

Interior:

1. Lexen can be used.

MOTOR:

1. Long or Short can motors up to 30,000 RPM

TYRES:

1. FOAM TYRES ONLY.

NSR,SCALEAUTO OR SLOT.IT

 

NO Tyre softening, conditioning or treating is allowed.

Tyres cleaning with Shellite only.

Some of the cars eligible for this class.

AVANT SLOT:

Peugeot 908

Porsche Spyder

Audi

Pescarolo LMP

SLOTINGPLUS:

Raynard 2KQ

SCALEAUTO:

RadicalSR-9

Toyota GT-1

SLOT.IT:

Nissan R390 GT1

LOLA BO9/60S

Audi R8C

McLaren GTR

NINCO:

Acura.

Audi R8

SCX:

Audi R8

Audi R10

NSR:

Audi R18

Audi R8

Scalextric:

Porsche spyder

Peugeot

Lola Aston Martin 1-2

Audi R8

 

 

SLOT IT GROUP C RULES.

 

AXLE FRONT:

1. Original front axle.

2. Must be located in the original,unmodified front axle holders.

3. Side play may be adjusted by adding axle washers.

4.wheels must be inside the guards.

AXLE REAR:

1.Original rear axle bushings only,NO ball bearings.

2. Must be located in original,unmodified rear axle holders.

3. Side play may be adjusted by adding axle washers.

4.wheels must be on the inside of the guards.

BODY:

1.Only the original unmodified Slot.It group C in-line chassis is allowed.

2.Rear wings must be mounted on the body in the original position before the start of the race.Rubber supports can be added to prevent wings from breaking off.Must be in original position.

3.If the rear wing comes detached during the race,it must be re attached before the next bracket.

4.The windows must remain original and in place at all times.

5.The body must not be altered in any way.

6. All the body screws must be in place.Any screws may be used.

7. The rear spats can be removed on the XJ9 and XJ12 Jaguar.

8. Painted liveries are allowed making sure all the parts are used and numbers have to be in at least 3 places on the car.

Legal bodies.......

Mercedes Sauber C9

Mazda 787 B

Lancia LC 2

jaguar XJ9 and XJ12

Porsche 956 KH

Porsche 962 C

Porsche 956 C

Toyota 88 C

Nissan R89C

CHASSIS:

1.Only the original unmodified Slot.It group C chassis is allowed.

2. Adding weight to any part of the chassis is allowed.

3. Reinforcing or gluing parts of the chassis such as axle bushings,motor mounting post is allowed.

4. NO MAGNETS.

5. Opening screw holes to stop screws from catching is aloud.

6. Light scrape is aloud of chassis to stop body catching

GEARS:

1.Original Slot.It YELLOW 28T crown in-line gear.

2.Original Slot.It 9T pinion.

GROUND CLEARANCE:

1. Day light must be seen.

GUIDE:

1.Any Slot.It replacement guide.

2.Any lead wire.

3.Any braid.

INTERIOR:

1.Original unmodified interiors must be in place at all times.

MOTOR:

1.Original unmodified 21,500rpm slot.it group C motors only.

2.The motor tabs holding the end bell must not be tampered with in any way,otherwise it will be disqualified.

3.Cars that came with the 25,000rpm motor can change them to a 21,500rpm motor.

WHEELS/TYRES FRONT:(NO SILICON TYRES.)

1.Only original slot.it group C tyres are permitted.

2.Sanding gluing and truing is allowed.

3.Tyres must touch on set up board when checked.

4.Original rims only.

WHEELS/TYRES REAR:(NO SILICONS TYRES.)

1.FOAM TYRES ONLY. SLOT IT foam to suit slot it wheels part number WH1211-AL OR WH1190-AL/NSR PART NUMBERS 9024 AND 9025/SCALEAUTO SC-2009P

2.Sanding gluing and truing is allowed.

3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED.

 

 

Sideways GROUP 5 RULES.

 

AXLE FRONT:

1. Original front axle.

2. Must be located in the original,unmodified front axle holders.

3. Side play may be adjusted by adding axle washers.

4.wheels must be inside the guards.

AXLE REAR:

1.Original rear axle bushings only,NO ball bearings.

2. The offset axel holders can replace the standard that come in the car as these parts are with the car as spare options.

3. Side play may be adjusted by adding axle washers.

4.wheels must be inside the guards.

BODY:

1.Only the original unmodified Group 5 angel winder chassis is allowed.

2.Rear wings must be mounted on the body in the original position before the start of the race.Rubber supports can be added to prevent wings from breaking off.Must be in original position.

3.If the rear wing comes detached during the race,it must be re attached before the next bracket.

4.The windows must remain original and in place at all times.

5.The body must not be altered in any way.Light scrape is aloud to stop body catching on chassis.

6. All the body screws must be in place.Any screws may be used.

7. Painted liveries are allowed making sure all the parts are used and numbers have to be in at least 3 places on the car.

 

CHASSIS:

1.Only the original unmodified sideways group 5 anglewinder chassis is allowed.

2. Adding weight to any part of the chassis is allowed.

3. Reinforcing or gluing parts of the chassis such as axle bushings,motor mounting post is allowed.

4. NO MAGNETS.

5. Opening screw holes to stop screws from catching is aloud.

6. Light scrape is aloud of chassis to stop body catching

GEARS:

1.Original Slot.It YELLOW 28T anglewinder gear.

2.Original Slot.It 11T pinion.

GROUND CLEARANCE:

1. Day light must be seen.

GUIDE:

1.Any Slot.It replacement guide.

2.Any lead wire.

3.Any braid.

INTERIOR:

1.Original unmodified interiors must be in place at all times.

MOTOR:

1.Original unmodified 20,500rpm slot.it motors only. They are Slot-it motors that are released in sideways cars.

2.The motor wrapper has to be in tact,otherwise it will be disqualified.

3. Note the first lot of Capri cars were released with a open can both sides .These motors a still rated with the same everthing to what comes in the sideways cars to date.

Anyone wishing to replace a motor can use the 20,500rpm Slot-it motor part number MN0O9CH. Motor label must be on.

 

WHEELS/TYRES FRONT:(NO SILICON TYRES.)

1.Only original slot.it tyres are permitted.

2.Sanding gluing and truing is allowed.

3.Tyres must touch on set up board when checked.

4.Original rims only.

WHEELS/TYRES REAR:(NO SILICONS TYRES.)

1.FOAM TYRES ONLY. SLOT IT/NSR PART NUMBERS 9024 AND 9025/SCALEAUTO SC-2009P

2.Sanding gluing and truing is allowed.

3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED.

Ford Capri

935/78

BMW M1 320i

LANCIA BETA MONTECARLO

Ferrari 512BB Group 5

Ford Mustang

 

 

SCALEXTRIC GT MAGNET RULES (AMATEUR ONLY)

 

THIS IS A MAGNET RACED CLASS. MAXIMUM DOWNFORCE READING ON THE MAGNET MARSHALL WILL BE 350.

NOTE YOU CAN ONLY RUN 1 MAGNET,BUT CHANGING OF MAGNET IS ALLOWED AS LONG AS IT FITS IN ORIGIANAL

POSITION AND DOSNT EXCEED 350 DOWNFORCE.

NO HIGH IMPACT CARS ALLOWED IN THIS CLASS.

AXLES FRONT.(Front wheels can exceed.5 of a mm out side the guard on either side of original set up)

1. Original front Axel set up.

2.Must be located in original,unmodified front axle holders.

3.Side play may be adjusted by adding axle spacers.

AXLES REAR.(Rear wheels can exceed .5 of a mm out side the guard on either side of original set up.)

1.Original rear axle and bushings only.NO BALL BEARINGS.

2.Must be located in the original ,unmodified rear axle holder.

3.Side play may adjusted by adding washers.

Body.

1.Original unmodified Scalextric GT style bodies are allowed.

2.Rear wings must be mounted in original position before the start of a race.They also can be mounted with rubber supports to help prevent wings breaking off.Must remain in original position.

3.The windows must remain original and clear at all times.

4.The body must not be altered in any way and must have a .5mm ground clearance of the track surface.

5.Any screws may be used.Screws may be left loose.

6.Light shave of body is allowed to stop body catching on chassis.

7.Posts can be sleeved for more support and strenght to prevent breakages .

8.Painted liveries are allowed as long as all parts are used and 3 numbers are in place on the car.

Chassis.

1.Only the original unmodified Scalextric GT style chassis is allowed.

2.Adding weight to any part of the chassis is allowed.

3.Gluing of bearings and gluing motor in is allowed.

4. Slight shave of the chassis is allowed to top from catching on the body.

5.Post holes can be opened up to stop screws catching.

Gears.

1.Original plastic drive gear.

2.Original drive gear.

Ground Clearance.

1. 0.5mm clearance under hole chassis.

Guide.

1.Original guide.

2.Any lead wire.

3.Any braid.

Interior.

1.Original unmodified interiors in place at all times.

Motor.

1.Original Scalextric 18,000 rpm motors only.

2.The sealed motors can not be tampered with in any way.

3.Motors can be glued or taped in.

4.Resistors can be removed.

5.Lights can be removed or disconnected.

Wheels/Tyres FRONT.

1.Original Scalextric only.Truing and gluing is allowed.

2.The front wheels must touch the flat surface when placed on the set up board.

3.Original rims only.

Wheels/Tyres REAR.

1.Original Scalextric tyres and the only replacement is MJK. Gluing and truing is allowed.

2.Original rims only.

3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED. Tyre shore hardness may be checked against original packet standard tyres.

 

Some of the eligible cars for this class.

Aston Martin (NO pro performance car)

Audi r8 LMS

Dodge Viper

Ferrari 330

Ferrari F430,F430 GT,F430GTR,and F430 GT2.

Ford GT .

Honda nsx

Jaguar XKR,XKRS and GT3

Lamborghini Gallardo

Maserati MC12

Maserati Cambiocorsa

Mclaren MP4 12C

Mclaren 722 GT

Mercedes SLR

Mercedes GT1 Lemans

Nissan GT-R

Nissan Skyline

Nissan 350Z

Porsche GTR3

Porsche 997 GT3/ with exception of the flying Lizard which has a 20,000rpm motor.

Toyota Supra

 

 

SCALEXTRIC Aussie v8's MAGNET RULES (AMATEUR ONLY)

 

THIS IS A MAGNET RACED CLASS. MAXIMUM DOWNFORCE READING ON THE MAGNET MARSHALL WILL BE 350.

NOTE YOU CAN ONLY RUN 1 MAGNET,BUT CHANGING OF MAGNET IS ALLOWED AS LONG AS IT FITS IN ORIGIANAL

POSITION AND DOSNT EXCEED 350 DOWNFORCE.

NO HIGH IMPACT CARS ALLOWED IN THIS CLASS.

AXLES FRONT.(Front wheels can exceed.5 of a mm out side the guard on either side of original set up)

1. Original front Axel set up.

2.Must be located in original,unmodified front axle holders.

3.Side play may be adjusted by adding axle spacers.

AXLES REAR.(Rear wheels can exceed .5 of a mm out side the guard on either side of original set up.)

1.Original rear axle and bushings only.NO BALL BEARINGS.

2.Must be located in the original ,unmodified rear axle holder.

3.Side play may adjusted by adding washers.

Body.

1.Original unmodified Scalextric V8 style bodies are allowed.

2.Rear wings must be mounted in original position before the start of a race.They also can be mounted with rubber supports to help prevent wings breaking off.Must remain in original position.

3.The windows must remain original and clear at all times.

4.The body must not be altered in any way and must have a .5mm ground clearance of the track surface.

5.Any screws may be used.Screws may be left loose.

6.Light shave of body is allowed to stop body catching on chassis.

7.Posts can be sleeved for more support and strenght to prevent breakages .

 

Chassis.

1.Only the original unmodified Scalextric V8 style chassis is allowed.

2.Adding weight to any part of the chassis is allowed.

3.Gluing of bearings and gluing motor in is allowed.

4. Slight shave of the chassis is allowed to top from catching on the body.

5.Post holes can be opened up to stop screws catching.

Gears.

1.Original plastic drive gear.

2.Original drive gear.

Ground Clearance.

1. 0.5mm clearance under hole chassis.

Guide.

1.Original guide.

2.Any lead wire.

3.Any braid.

Interior.

1.Original unmodified interiors in place at all times.

Motor.

1.Original Scalextric 18,000 rpm motors only.

2.The sealed motors can not be tampered with in any way.

3.Motors can be glued or taped in.

Wheels/Tyres FRONT.

1.Original Scalextric only.Truing and gluing is allowed.

2.The front wheels must touch the flat surface when placed on the set up board.

3.Original rims only.

Wheels/Tyres REAR.

1.Original Scalextric tyres and the only replacement is MJK. Gluing and truing is allowed.

2.Original rims only.

3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED. Tyre shore hardness may be checked against original packet standard tyres.

 

2017 NSR Classic Regulations

AXLES FRONT:

1.Original front axle.

2.Must be located in original, un-modified front axle holders.

3.Side play may be adjusted by adding axle washers.

4.wheels must be inside the guards.

AXLES REAR:

1.Original rear axle bushings only.

2.Must be located in the original, un-modified rear axle holders.

3.NO BALL BEARINGS.

4.wheels must be inside the guards.

BODY:

1.NSR Classic body only.

2.Painted liveries are allowed. Numbers have to be in at least places on the body.

3.Srew posts can be sleeved for extra support to prevent breakages.

4.If the car comes with the dummy spare wheel it must remain in the car as it come.

CHASSIS:

1.Only the NSR classic chassis for the make of car be used (Porsche to Porsche etc.)

2.Adding weight to any part on top of the chassis inside the car is allowed.

3.Reinforcing or gluing parts of the chassis such as axle bushings, motor mounting posts etc. is allowed.

4.No chassis magnets are allowed.

GEARS:

1.NSR GEARS ONLY. Gear ratio is 11/32.

GROUND CLEARANCE:

1.Day light must be seen.

GUIDE:

1.Any wood track guide.

INTERIOR:

1.Original un-modified interiors must be in place at all times.

MOTOR:

1.Un-modified small can shark 20,000rpm motors only (comes standard in all NSR classic cars).

2.Side winder set up only.

3.The motor may be glued or taped in.

4.The motor tabs must remain intact. Any tampering will result in disqualification.

5.Motor labels must be intact. Orange 20,000rpm.

WHEELS/TYRES FRONT: (NO Silicon)

1.Any front tyre.

2.Sanding/truing tyre is permitted.

3.tyres must touch the track surface. Allowance will be made as these cars released the fronts do not always touch the set up board.)

4.Original rims only.

WHEELS/TYRES REAR: (NO Silicon)

1.FOAM TYRES ONLY....NSR PART NUMBERS 9024 AND 9025/SLOT IT/SCALEAUTO SC-2009P

2.Sanding/Gluing and truing is allowed.

3.TYRE TREATING, SOFTENING OR CONDITION OF ANY KIND IS NOT ALLOWED.

4.Cleaning with Shellite ONLY is allowed.

 

Thanks

Greg Colgan

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

×
×
  • Create New...