Jump to content
ZeGas

Rc Restarts Computer

Recommended Posts

I have RC V1.10 running on an XP machine.

It consistently but at random periods restarts the computer.

Either open but idle or in the middle of a race.

 

Also have RCD on the same computer and it does not affect the computer at all.

Has anyone else experienced this.

 

I am timing through Arduino, not sure if this might be the issue.

Dave's latest sketch is installed (10/03/16).

 

Wondering if there is a known fix before I hassle Dave.


Cheers Grant

20191120172309-193d8f3b.gif.......................................................20170306174707-b4015afe.gif

Home Track..........Corvette C1 Build..........McLaren M1A Build..........Maserati 300S Build..........Allard J2 Build..........50's Diner..........Iso Griffo A3C

 

3D Printed Adjustable Chassis..........3D Print Projects

Share this post


Link to post
Share on other sites

Are you sure the pc is 100% stable?

I've not heard of RC restarting a pc before.

Share this post


Link to post
Share on other sites

The more I look into it I think it might be arduino rather than RC. There might be a port conflict, this would be consistent as RCD works fine.

the computer is stable it is on 24 hours as my weather station reports to it.

I have a feeling the weather station port conflicts with the arduino port although they are different.

I'll keep testing.


Cheers Grant

20191120172309-193d8f3b.gif.......................................................20170306174707-b4015afe.gif

Home Track..........Corvette C1 Build..........McLaren M1A Build..........Maserati 300S Build..........Allard J2 Build..........50's Diner..........Iso Griffo A3C

 

3D Printed Adjustable Chassis..........3D Print Projects

Share this post


Link to post
Share on other sites

Hey Phil,

 

No to first Q and I haven't tried a ferrite band on the USB, next time I'm up at Jaycar I'll grab one and try it.

Thanks for the tip.


Cheers Grant

20191120172309-193d8f3b.gif.......................................................20170306174707-b4015afe.gif

Home Track..........Corvette C1 Build..........McLaren M1A Build..........Maserati 300S Build..........Allard J2 Build..........50's Diner..........Iso Griffo A3C

 

3D Printed Adjustable Chassis..........3D Print Projects

Share this post


Link to post
Share on other sites

I found a cable with a ferrite block on it and connected it up.

No better, still restarts computer.

 

I'll try on another computer to see if it is a computer thing but I'm leaning towards the UNO board at the moment.

I don't have a power supply to the board just the USB power.


Cheers Grant

20191120172309-193d8f3b.gif.......................................................20170306174707-b4015afe.gif

Home Track..........Corvette C1 Build..........McLaren M1A Build..........Maserati 300S Build..........Allard J2 Build..........50's Diner..........Iso Griffo A3C

 

3D Printed Adjustable Chassis..........3D Print Projects

Share this post


Link to post
Share on other sites

I've not used an external supply on any of the 6x Arduino installs I've done...

And, some of those are driving 15 LED's on top of the normal sensors / switches.

 

That said, if something is shorting out on the arduino board, then yes, it will be causing an issue.

 

 

You haven't accidently wired a sensor accross Gnd and +5v have you? Possibly thinking it was an LED?

 

Best thing to do is remove all wiring from the arduino, start RC and run a race.

If it doesn't crash, re-add the lap sensor (using a desk lamp above it for the light source), and test again.

Then re-add the transmit LED (which should be translucent blue in colour if it's a IR LED), and test yet again.

Share this post


Link to post
Share on other sites

Just tested it on my other computer and it hasn't crashed yet.

I'm now wondering if it is an XP thing, I am updating all of that now

It had .net 3.5 on it so am updating to .net4 to see if that helps.

 

Your right SR baby steps and I'm sure I'll get to the root of the problem.

I had checked for shorts first up, I thought that might have been an issue.

I am running the light bridge power separate to the Arduino setup.

Only thing running of Arduino at the moment is the one sensor and the start lights so shouldn't be draining anything.

The bummer is that by the time I get to look at the blue screen report it disappears not enough time to take a photo of it either.


Cheers Grant

20191120172309-193d8f3b.gif.......................................................20170306174707-b4015afe.gif

Home Track..........Corvette C1 Build..........McLaren M1A Build..........Maserati 300S Build..........Allard J2 Build..........50's Diner..........Iso Griffo A3C

 

3D Printed Adjustable Chassis..........3D Print Projects

Share this post


Link to post
Share on other sites

I doubt that it's XP or .net as Digital works fine.

It is possible that the PC has to work harder for analog mode, which could cause a crash where other apps do not...

 

If it's a hardware fault on the PC, check for bloated caps, dirt in the fans/heatsinks, and dry cracked up heatsink paste on the CPU.

99% of the time, it's one of those 3 that cause intermittent crashing on older PC's.

 

BLoated Caps

500x1000px-LL-3ecd48e3_leaking-dell-capacitors.jpeg

 

Dry Heatsink Paste

DSC01924.jpg

Edited by shadow_rusty

Share this post


Link to post
Share on other sites

Wow, looks like you have had problems.

 

I think it was a combo of things, old .net frame work and install of RC.

 

I installed the latest version of .net for XP and uninstalled RC.

Cleaned the computer of redundant files relating to RC and reinstalled.

1/2 hour test last night and 1/2 hour this morning and so far stable.

 

I did try the latest Beta version of RC but it looses connection on first lap, both computers so went back to latest release for both computers.

 

Hopefully that's the end of it and I can get back to building.

 

Thanks for your input Michael, greatly appreciated as always.

Edited by ZeGas

Cheers Grant

20191120172309-193d8f3b.gif.......................................................20170306174707-b4015afe.gif

Home Track..........Corvette C1 Build..........McLaren M1A Build..........Maserati 300S Build..........Allard J2 Build..........50's Diner..........Iso Griffo A3C

 

3D Printed Adjustable Chassis..........3D Print Projects

Share this post


Link to post
Share on other sites

Glad it's now sorted...

Normally though, RC won't install if .net is not the correct version, so that was weird...

 

 

ps. Those weren't my machines, but I do work in deskop support, so I have seen my fair share of faulty PC's...

Edited by shadow_rusty

Share this post


Link to post
Share on other sites

Well that was short lived, back to square one.

I'll try and find some time in the weekend to pull the laptop apart and check out your advice SR, but I'll also find a power supply for the Arduino Board just to check that as well.

I'm sure I'll have a 5v -9v supply hanging around somewhere.


Cheers Grant

20191120172309-193d8f3b.gif.......................................................20170306174707-b4015afe.gif

Home Track..........Corvette C1 Build..........McLaren M1A Build..........Maserati 300S Build..........Allard J2 Build..........50's Diner..........Iso Griffo A3C

 

3D Printed Adjustable Chassis..........3D Print Projects

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.


×
×
  • Create New...