wwwace Posted April 19, 2016 Report Share Posted April 19, 2016 2016 REGULATIONS 1/24 FORMULA LeMANS 1.0 BODY 1.1. Only 1/24 ACE #24009 Oreca FLM09 Body Kit is allowed to be used. 1.2. Minimum rear wing height is 42.0mm (measured at rear of car ground to top). 1.3. Fantasy liveries in the spirit of 1:1 FLM, LMP Racing are permitted. 1.4. Light set ZMachine 165Q is required for the APC 2014. 1.4. Minimum body weight including body mounts is 18.0 g. 2.0 CHASSIS 2.1. Only Plafit 1800SLPJ Chassis and its kit parts can be used. 2.2. Axle Bearing Holders 1709 (B,C,D) can be used. 2.3. 1708G and 2808J Motor Brackets can be used. 2.4. 1711G and 2811J Motor Stays can be used. 2.5. Aftermarket Carbon replacement parts are allowed as long as they are commercially available. 2.6. Chassis has to be adjusted according to the body and its dimensions making sure that all wheels are covered by the body when viewed from above. 2.7. All original mounting points and basic configuration must be retained. 2.8. No chassis modifications other then within its design limits. 2.9. No soldering permitted to hold motor into position. Only motor screws are to be used. 2.10. No traction magnets. 2.11. Body tape or plastic strip may be used to hold lead wires in place. 2.12. Additional weight may be placed into the centre openings of the main chassis plate in accordance with the minimum ground clearance rule. 3.0 GROUND CLEARANCE 3.3. 1.0mm under the entire chassis including gear. 4.0 FRONT AXLE 4.1. Any 3mm non. Independent front axles allowed. 4.2. Any 3mm axle oilites or axle ball bearings allowed. 5.0 FRONT WHEELS 5.1. Any Aluminum front wheels with a minimum diameter of 21mm can be used. 5.2. Sakatsu Brake Discs (2100) are to be used with all Sakatsu wheels. 5.3. 3D Wheel Inserts in modern LMP/GT design have to be used. 5.4. Any Hard Sponge Tires sealed or non-sealed can be used. 5.6. Minimum tire and rim width is 6mm. 5.7. Minimum tire diameter is 26.0mm. 5.8. Maximum front spur width is 86.0mm but never wider then the body. 6.0 REAR WHEELS 6.1. Any Aluminum rear wheels with a minimum diameter of 21mm can be used. 6.2. Sakatsu Brake Discs (2100) are to be used with all Sakatsu wheels. 6.3. 3D Wheel Inserts in modern LMP/GT design have to be used. 6.4. Maximum tire and rim width is 16mm. 6.5. Minimum tire diameter is 26mm. 6.6. Maximum rear spur width is 86.0mm but never wider then the body. 6.7. Plafit Black Magic Rear Tires (8441BM or 8442BM) and Scaleauto ProComp3 Tires are allowed only. 6.8. Use of Goo and/or any other tire softener, liquids etc. is not allowed. Cleaning with Tape or Shellite only is permitted. 7.0 REAR AXLE 7.1. Any 3mm. 7.2. Any 3mm axle oilite bushings or axle ball bearings can be used. 8.0 GEARS 8.1. Any plastic 50 pitch spur gears for 3mm axles. 9.0 PINION 9.1. Any 50 pitch. 10.0 MOTOR 10.1. 13D 8635 Fox IV Motor only. 10.2. Original lettering on the motor can has to be visible. 10.3. Sealed Motors are not to be opened or modified in any way. 10.4. Any lead wire. 10.5. Different motors will be nominated at certain race events. 11.0 WEIGHT 11.1. Minimum total car weight is 155g. 12.0 REPAIRS 12.1. The following repairs must be carried out immediately under Green Light (race condition): (a) replacing or refitting the rear wing* ( replacing or refitting the driver figure including the driver head* *can be done with tape 12.2. All repairs must be carried out under green unless specifically approved by the Race Direction. Link to comment Share on other sites More sharing options...
Recommended Posts