Jump to content

Regulations 1/32 Plafit Us Muscle Cars


wwwace

Recommended Posts

2016 REGULATIONS 1/32 US MUSCLE CARS

 

1.0 BODY

1.1 Only 1:32 US Muscle Cars made from hard plastic which are nominated on the

Official Homologation List are allowed.

1.2. No major body modifications such as changes to wheel arches or shortening of

under body parts are allowed.

1.3. Original body mounting posts on the body inside can be removed.

1.4. Replacement Lexan interior ACE32-1 can be used. To be cut to cover all windows.

1.5. Under body front spoilers (fenders) and rear diffusers have to be retained from all

four relevant wheel arches and fitted to the body.

1.6. Front under body clearance for the guide can be removed behind the front spoiler.

1.7. All original outside detail parts like mirrors and rear wings etc. are to be used at all

times.  

2.0 CHASSIS

2.1. Plafit 3300 Super32 in 3mm versions only.

2.2. Chassis is to be adjusted according to the body and its dimensions making sure

that the guide is covered by the body when viewed from above.

2.3. All Plafit 3300 chassis system parts can be used except Flat Body Mount Plates

System (3307B, B1, B2, C and D). Only 3307 can be used for body mounting.

2.4. Chassis springs, spacers and/or additional screws may be substituted, added or

removed.

2.5. All original mounting points and basic configuration must be retained.

2.6. Chassis is to be adjusted according to the body and it’s dimensions making sure

that all wheels are centred in the wheel arches. For narrow body cars

(eg: Mustang / Mercury etc.) the wheels may extend past the body guards but only

1.0mm maximum each side provided the maximum spur width is not exceeded.

2.7. No chassis modifications other then within its design limits.

2.8. ACE Carbon replacement guide holder can be used.

2.9. No soldering permitted to hold motor into position. Only motor screws can be used

2.10. Body tape or plastic strips may be used to hold lead wires in place.

2.11. Additional weight may be added on top of the chassis only.

2.12. Nylon Guide Nuts can be used.

2.13. Plafit 1717A + 1717B Stabilizer Kits or parts thereof may be used.

2.14. No Traction Magnets

2.15. Chassis blue-printing is allowed. No excessive sanding for weight reduction !

2.16. Maximum polar length is 93.0mm.

3.0 FRONT AXLE

3.1. Any solid 3mm only. No independent front axles/wheels allowed.

3.2. Any 3 x 6mm axle oilite or axle ball bearings can be used

4.0 FRONT WHEELS and TIRES

4.1. Only Plafit 801406-RTR Wheels/Tires can be used. Tires surface can be sealed.

4.2. Minimum tire diameter is 18.0mm.

4.3. Minimum tire width is 6.0mm.

4.4. Maximum front spur width is 58.0mm.

4.5. 3D Wheel Inserts related in design to the actual car have to be used at all times.

5.0 REAR WHEELS and TIRES

5.1. Only Plafit 801411-RTR Wheels/Tires can be used.

5.2. For replacement sponge rubber only Black Magic Sponge can be used.

5.3. Minimum wheel/tire diameter is 19.0mm.

5.4. Maximum wheel/tire width is 12.0mm.

5.5. Maximum rear spur width is 59.0mm.

5.6. Use of Goo and/or any other tire softener, liquids etc. is not allowed. Cleaning with

Tape or Shellite only is permitted.

5.7. 3D Wheel Inserts related in design to the actual car have to be used at all times.

6.0 REAR AXLE

6.1. Solid 3mm metal only.

6.2. Any 3 x 6mm axle oilite or axle ball bearings can be used.

7.0 GROUND and BODY CLEARANCE

7.1. Minimum 1.0mm under the entire chassis including gear.

7.2. Minimum 1.0mm front of body including any spoiler.

7.3. Minimum 4.5mm to body rear directly in front of rear wheel arch.

Side pipes are not part of the body

Exception : Only the Ford Falcon XB can have 3.5mm clearance.

(Note: As a guide Plafit Mounting Rubber is 4.5mm thick).

8.0 WEIGHTS

8.1. Minimum total car weight is 120 gr.

9.0 GEARS

9.1. Any plastic 50 pitch spur gear.

10.0 PINION

10.1. Any 50 pitch.

11.0 MOTOR

11.1. Plafit 8630 Rabbit Motor (MCN + APC hand-out).

11.2. Original letterings have to be visible.

11.3. All motors are not to be opened or modified in any way.

11.4. Any lead wire can be used.

 

1/32 PLAFIT US MUSCLE CARS

Official Body Homologation List 2016 for Plafit US Muscle Cars

 

CARRERA

Chevrolet Camaro SS396

Chevrolet Camaro Super Stocker

Chevrolet Chevelle SS 454 '70

Chevrolet Corvette GT 350

Ford Mustang GT '65

Ford Mustang '67

Plymouth Hemi Cuda

Pontiac Firebird TransAm '77

 

MONOGRAM

Shelby Mustang

Chevrolet Corvette Grand Sport

Pontiac Firebird Model Kit

Chevrolet Camaro Z28 Model Kit

Ford Mustang GT350 Model Kit

Ford Boss Mustang Mach 1 + 2 Model Kit

Chevrolet Corvette Grand Sport

Chevrolet Corvette Model Kit

Chevrolet Camaro '69 Model Kit

AMX 390 Model Kit

Barracuda Formula S Model Kit

Mercury Cougar GT-E Model Kit

Javelin SST Model Kit

 

MPC

Pontiac Firebird SNAP Model Kit

Chevrolet Corvette SNAP Model Kit

 

PIONEER

Chevrolet Camaro SS

Ford Mustang

 

SCALEXTRIC

Chevrolet Camaro Z28

Chevrolet Camaro SS

Chevrolet Corvette

Dodge Challenger

Ford Mustang

Ford XB Falcon

Mercury Cougar XR7

 

SCX

Plymouth Barracuda

 

20.12.2015

Note : Only cars with solid roofs are allowed. No convertibles and targa styles.

This list does not claim to be complete.

Changes and updates will be made if necessary.

Link to comment
Share on other sites

Guest
This topic is now closed to further replies.
×
×
  • Create New...