Jump to content
Sign in to follow this  
wwwace

Regulations 1/32 Slot.it Group C

Recommended Posts

2016 SLOT.IT GROUP C REGULATIONS

 

AXLE FRONT:

1. Original front axle.

2. Must be located in the original, un-modified front axle holders.

3. Side play may be adjusted by adding axle washers.

4.Wheels must be inside the guards.

 

AXLE REAR:

1.Original rear axle bushings only, NO ball bearings.

2. Must be located in original, un-modified rear axle holders.

3. Side play may be adjusted by adding axle washers.

4.Wheels must be on the inside of the guards.

 

BODY:

1.Only the original unmodified Slot.It group C in-line chassis is allowed.

2.Rear wings must be mounted on the body in the original position before the start of the race. Rubber supports can be added to prevent wings from breaking off. Must be in original position.

3.If the rear wing comes detached during the race, it must be re attached before the next bracket.

4.The windows must remain original and in place at all times.

5.The body must not be altered in any way.

6. All the body screws must be in place. Any screws may be used.

7. The rear spats can be removed on the XJ9 and XJ12 Jaguar also the Nissan R89C.

8. Painted liveries are allowed making sure all the parts are used and numbers have to be in at least 3 places on the car.

 

Legal bodies.......

Mercedes Sauber C9

Mazda 787 B

Lancia LC 2

Jaguar XJ9 and XJ12

Porsche 956 KH

Porsche 962 C

Porsche 956 C

Toyota 88 C

Nissan R89C

 

CHASSIS:

1.Only the original unmodified Slot.It group C chassis is allowed.

2. Adding weight to any part on top of the chassis inside the car is allowed.

3. Reinforcing or gluing parts of the chassis such as axle bushings, motor mounting post is allowed.

4. NO MAGNETS.

5. Opening screw holes to stop screws from catching is aloud.

6. Light scrape is aloud of chassis to stop body catching

 

GEARS:

1.Original Slot.It YELLOW 28T crown in-line gear.

2.Original Slot.It 9T pinion.

 

GROUND CLEARANCE:

1. Day light must be seen.

 

GUIDE:

1.Any Slot.It replacement guide.

2.Any lead wire.

3.Any braid.

 

INTERIOR:

1.Original unmodified interiors must be in place at all times.

 

MOTOR:

1.Original unmodified 21,500rpm Slot.it Group C orange endbell motors only.

2.The motor tabs holding the endbell must not be tampered with in any way, otherwise it will be disqualified.

3.Cars that came with the 25,000rpm motor can change them to a 21,500rpm motor.

 

WHEELS/TYRES FRONT: (NO SILICON TYRES.)

1.Only original Slot.it group C tyres are permitted.

2.Sanding gluing and truing is allowed.

3.Tyres must touch on set up board when checked.

4.Original rims only.

 

WHEELS/TYRES REAR: (NO SILICONS TYRES.)

1.FOAM TYRES ONLY. SLOT IT foam to suit slot it wheels part number WH1211-AL OR WH1190-AL/NSR PART NUMBERS 9024 AND 9025/SCALEAUTO SC-2009P

2.Sanding gluing and truing is allowed.

3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED.

Edited by wwwace

Share this post


Link to post
Share on other sites
Guest
This topic is now closed to further replies.
Sign in to follow this  

×
×
  • Create New...