Classes And Rules For The 2014 Scale Model Nationals

[Guest jazzbell]

Classes for the 2014 scale Nationals will be as

 

Ninco GT

NSR Classic

SCX Nascar

Slot.It Group C

Scalextric GT/ Magnet class

Open class LMP/PROTO

Plafit 1/32 DIV1/DIV 2 will be grouped together .

PLAFIT1/27 Minni Z

plafit 1/24 can am

1/24 Scaleauto

1/24 Nascar

 

All racing will be done on the pitstop 6 laner. The Scalextric magnet GT class will be raced on the 6 lane Diggers track.

 

2014 Model Car Nationals Presented by Extremetrax NSW. General rules and regulations. Cost per class to enter is $15.

Officals and Dutie:

1. The event organiser may appoint a Race director of acceptable knowlage and experience for each of the classes.

2. The Race Director may act as scrutineer and/or Race Controller or he/she may appoint an acceptable deputy to fill this positions.

3. The race director is responsible for all aspects of the running of racses in his/her charge.

4. The Scrutineer is responsable for ensuring that all cars conform to specifications for their class and relevant general rules.

5. The Race Controller is responsible for overseeing a particular race. Initiating Track Calls,directing marshalls,ect.

 

Cars And Scrutineering:

1. Cars must comply with the specifications for their class and any relevant regulations at all times whilst racing.

2. Cars that do not conform to the relevant specifications shall be excluded from the event.

3. Cars must be submitted to the scrutineer prior or at the advertised time for the class.

4. Scrutinneers word is final.

5. The scrutineer is empowered to rule on any area of a cars construction not specifically coverd by the rules.

6. Cars will be scrutineered prior to each race/heat.

7. Cars can be scrutineered at any time or a teardown inspection at the descretion of the Race Director/Controller.

 

Impounding Of Cars(PARK FERME):

1. The event organiser will provide a safe area where cars will be impounded. Typically they stay in park ferme after scrutineering until they are eliminated from the completion of racing.

2. Drivers may remove cars from PARK FERME prior to qualifying and must return the car back after they qualify to the PARK FERME . Like wise after racing cars have to be returned to PARK FERME.

3. All cars stay impounded until end of racing.

 

Repairs and Parts Replacements:

1. All repairs and replacement components must comply with the specifications for the relevant class.

2. Any part may be replaced with the exception of the primary chassie section and the body shell.

3. All the repairs and parts replacements during the race event is subject to re scrutineering.

 

DRIVER CONDUCT:

1. Drivers and their pit crew are expected to conduct themselves in a professional manner at all times.

2.Abusive,offensive or unsportmanlike conduct directed at any person will result in immediate penalties being aposed.

3. Driver are also cautioned that they might be held responsible for the actions of their pit crew.

 

Smoking: In the interests of health and saftey,there will be stricly NO smoking in the racway.

 

MARSHALLING

1. All entrants will marshall.

2. Entrants may nominate a substitute marshall.

 

DUTIES of MARSHALS

1. Clear the track of de-slotted or malfunctioning cars.

2. Re place de slotted cars without interfering with the other cars.

 

CONTROLLERS:

1. Any hand controller can be used as it does not increase the voltage or available amps to the track.

 

DISPUTES and INTERPRETATION of the RULES.

1.The race Directors decision is bound and final,and their is no appeal on the decision. P

 

PENALTIES: Any deliberate rule infraction contrived to gain a performance advantage will result in exclusion from the class.

 

BLACK FLAG:

1.The race controller can demand the removal from the track of any car wich is dragging on the track,interfering with other cars,or continually de-slotting.

2.Any car that cannot complete a lap with out de-slotting will be black flagged.

3.Cars can be repaired and re enter the race.

 

TRACK POWER SUPPLY:

1.Nominal track voltage for racing will be at 12 volts for the 32scale rtr cars ,the scx nascar also could be at 13 volts.The scaleauto class will run on 12 volts. All the Plafit racing and mjk 24 scale will be raced at 13 volts.

2.Depending on what class a higher voltage will be used .Race directors decision will be final on this.

Edited January 20, 2014 by jazzbell

[Guest jazzbell]

1/24^th Scale Auto Regulations 2014 (as used in Australia)

 

1.1.0. GENERAL DESCRIPTION

(a) The only cars permitted to enter are:

(i) The Scale Auto Porsche 911 GT3 RSR(997). (Not the GT3 Rally or GT3 Cup versions).

 

 

(ii) The Scale Auto BMW M3 GT2.

 

 

(iii) The Scale Auto Jaguar XKR-RSR GT2.

 

 

(iv) The Scale Auto Mercedes Benz SLS GT3.

 

 

(v) The Audi R8 LMS GT3.

 

 

(vi) The BMW Z4 GT3

 

 

(b ) It is the responsibility of the racer to ensure that the purchased Scale Auto cars are accurate, complete and without missing parts. (Including small plastic and photo edged parts.)

(c ) An original example of homologated Scale Auto cars as described by Art.1.1.0 (a) will be at Technical Control as reference for the Technical Director and Scrutineers. In the case of all disputes, the judgement of the Technical Director (or race jury) will be final and binding.

(d) All of the chassis and body parts that come with the Scale Auto cars as described in Art. 1.1.0.(a) must be used. See Rules-Pictures for additional clarification.

 

 

 

 

If a part is shown in these pictures it must be on the car according to the manufacturer's intended mounting and location. The only exceptions are as follows: Art. 1.1.3. (b ).

 

1.1.1. MODIFICATIONS

(a) It is not permitted to modify the RTR car or white kit in any way other than those parts of free make as described by Art. 1.1.1 (b )

(b ) Parts of free make are restricted to: (i) nuts, bolts, spacers and washers, (ii) the guide and guide nut, (ii) braid, braid clips & lead wires, (iv) axles (v) axle bearings, (vi) ballast lead weights, (vii)3 –dimensional wheel inserts, (viii) M50 spur gear, (ix) M50 pinion gear (check on correct size for the proposed hand out motor).

(c )Scale Auto tuning parts including the carbon H-plates, spring plates, guides holders, different height axle holders, carbon rear wings (excluding the wing supports) etc. are NOT permitted.

 

 

1.1.2. WEIGHT, DIMENSIONS & GROUND CLEARANCE

 

(a) The minimum weight for a complete Scale Auto car is 190g.

 

 

(b )The minimum weight for the body with the body mounts and fixing screws attached is 55g.

 

 

(c) The ground clearance will be measured with the guide out of play so that all four wheels sit flat on the tech block.

(d) The ground clearance at the start of every race is never less than 1.8mm.

(e) The ground clearance during or at the end of any race is never less than 1.40mm (if found to be in breach during the race, it must be rectified under green - if after the end of the race; it will result in the loss of the total laps scored in the best race bracket during the race).

(f) Additional weighting of the body can only be applied to the vertical surfaces of the plastic reinforcing strips within the boundaries as shown in this picture.

 

 

(g) The distance from the top of the H plate to the bottom of the chassis plate is never more than 4.0mm.

(h) Additional weighting of the chassis may only be on top of the chassis, NOT visible when viewed from below.

 

1.1.3. CHASSIS (only non-drop arm version).

 

(a) The chassis must be assembled with screws and/or nuts and bolts using the original mounting holes.

(b ) The chassis must be assembled in the exact manner and orientation of the production RTR car. In this instance it is noted that some RTR cars are shipped with the guide holder mounted below and other above the T-plate. It is therefore up to the racer to decide which position he prefers for the guide holder on his car.

(c) The chassis plates may be flat sanded to remove burrs, sharp edges and swelling.

(d) The original mounting holes can be re-countersunk to properly seat the screws.

(e) The original MSC/Scale Auto logo on the bottom face of the main chassis plate must remain visible to the Technical Control.

 

 

(f) The original chassis plates, parts and metal body holders cannot be repainted or refinished in any way.

(g) The length of the guide blade cannot exceed 27, 0 mm and this guide blade is the only part of the chassis that may enter the track's slot.

(h) No part of the chassis may be visible when viewing the car from above.

 

1.1.4. MOTOR, GEAR AND PINION

 

(a)MOTOR FOR THE EVENT WILL BE THE NSR 25000 Evo.

 

MOTOR LABEL WILL BE REMOVED TO SHOW THE NSR 25,000 STAMP IS ON THE CASING,IF KNOW 25,000 PRINT MOTOR WILL NOT BE ALLOWED.

 

 

(b ) Soldering may only be used to attached the lead wires to the motor terminals.

(c )Motor coolers or heat dissipating products of any kind are not permitted.

(d) Only M50 pitch pinion and M50 spur gears are permitted.

(e) GEARING 10:44 for the NSR 25000 Evo motor.

 

 

1.1.5. AXLES, BEARINGS & WHEELS

 

(a) Only solid steel 3 mm diameter axle's front and rear are permitted. No independent front axle configurations of any kind are permitted.

(b ) Ball bearings for 3mm axles are permitted.

(c) Front wheels must be either the standard hard rubber wheels with rims as supplied with the RTR cars.The Scaleauto parts sc-2715p or sc-2709p may be used to achieve the 26.5mm minimum diameter.

 

 

(d) Each front wheel must make minimum 7.5mm of contact with the tech block with the guide out of play. Front tires may be hardened and polished.

(e) Rear wheels are RTR Scale Auto SC-2421P ProComp 3 wheels with 27,5mm OD, 13.0mm wide. At events where handout wheels and tyres are supplied, the hand out wheel and tyre diameters may not be changed and must be used as supplied. At events without hand out wheels and tyres, the rear wheel diameter may be altered, provided this Scale Auto part as quoted, is used. Altering the rear wheel diameter will not void the minimum starting ride height as per rule 1.1.2. (d).

 

 

(f) Rear tires may not under any circumstances be treated with any kind of tyre dressing, or compound or traction product.

(g) Removing dirt, dust and loose rubber particles from the tyres may only be performed with a tape roll or Shellite provided by the Race Direction.

(h) All four wheels must be fitted with three-dimensional wheel inserts (with or without brake discs and callipers) correct to the car. (No photo edged or vinyl cut reproductions will be allowed).

(i) The wheels may not protrude outside of the body when viewed from above.

(j) No car can have a front spur greater than 80mm or rear spur greater than 83mm, measured at the widest point of the front and rear axles. (This includes any protruding wheel inserts that may be fitted).

 

 

1.1.6. BODY & INTERIOR

 

(a) All bodies and interiors must be painted. (Interiors with at least three different colours and bodies with at least a coat of clear paint covering the complete outside of the body shell).

(b ) Fantasy liveries in the spirit of 1:1 motor sport are permitted.

(c )Three number shields typical of 1:1 motor sport are required.

(d) The stock rear wing uprights only may be replaced or reinforced with rubber parts of equal or like shape. The Scale Auto Carbon Rear wing may not be used, but the rubber wing mounts supplied with these wings may be used. (Should a wing go missing or get broken beyond repair a replacement part may be purchased as long as it is the original part as sold by Scale Auto. For example the BMW part number is SC-7612 and the Mercedes is SC-7614 etc).

(e) All the cars are permitted to use the full Scale Auto Lexan window and interior kits. Only the roll cage from the original hard plastic interior must be refitted to the lexan interior.

(f) Mirrors and wipers on some cars are very fragile and cars will be allowed to race without them when it is obvious that the mirror(s) has broken off. Drivers are encouraged to present cars with mirrors and wipers at the start of all races

(h) No modifications of the body are permitted other than those described by Art. 1.1.6(a-e)

 

 

1.1.7. ADDITIONAL NOTES & CLARIFICATION TO RACERS.

 

(a) Metal body mounting brackets SC-8117 can be used in place of the plastic part as first shipped on the Porsche 911 RSR GT3 cars in early 2010.

(b ) Only Scale Auto lexan interior and window kits may be used where allowed. (The air vent - photo below - that comes with the Audi lexan window and interior kit is not allowed).

 

 

(c ) The gas filler caps in the Mercedes that are molded into the lexan windows should be trimmed away so that the original plastic filler caps are used. This principal will also apply whenever a lexan part may be moulded with corresponding external body parts restricting the figment of the lexan window.

(d) When fitting the lexan interior the legs of the roll cage may be shortened to be able to fit it into the space between the lexan interior floor and the roof of the car. Currently this is only the case on the Mercedes SLS.

 

 

(e) The BMW Z4 white kits are supplied with four small front winglets, these may be used at the discretion of the builder. The body kit is also supplied with two different rear wing mounts. Either of these may be used. However, if the mounting legs are replaced with a flexible material, the secondary wing between the mounting legs must be retained.

 

 

or

 

 

(f) Racers are warned that cars with missing parts will not be allowed to enter. (Even if it was lost during practice or on the way to scrutineering).

(g) During lane changes no work on the cars at all will be allowed - work on the car may only be done under green.

 

END.

 

 

regards shane a

• 
  
• 
  

Edited January 20, 2014 by jazzbell

[Guest jazzbell]

KYOSHO MINI-Z GT RULES

 

 

1.0 BODY

1.1. Only Mini-Z Hard Plastic GT Bodies which are listed on the official body list are

allowed to be used. No street cars, race cars only which have to feature at least

two race numbers and some typical modern GT Car race sponsor logo decals.

1.2. White unpainted body kits can be used however all kit parts have to be included

during assembly. Body has to be painted and decaled.

1.3. All body detail parts like mirrors, windscreen wipers, wings etc. have to be

retained on the body at all times.

1.4. Rear wings can be rubber mounted. Aftermarket mirrors are allowed.

1.5. Ford GT has to have rear wing (AR-086 or AR-090) fitted.

1.6. The body holders (both sides and front) for the Kyosho display chassis can be

removed and sanded. No other part of the body can be sanded, lightened or

modified in any way.

1.7. All wheel arches are not allowed to be sanded and/or widened.

1.8. A two piece driver interior (vacuum formed with separate drivers head) is to be

used. The interior has to cover all windows and open cockpits. No chassis parts

are allowed to be visible. Half sized interiors are allowed and rear window plus

both rear side windows can be painted black from the inside.

 

2.0 CHASSIS

2.1. Plafit Excel 1300 and Plafit Super24 1700 only (no 1700G, GTC, GTX and SLP versions).

2.2. All Plafit 1300 and 1700 chassis system parts can be used except 1700G and

SLP parts. Plafit 3309, B and C in combination with 1705G/S/K can be used.

2.3. No chassis parts mixing between 1300 and 1700 chassis systems.

2.4. Chassis has to be adjusted according to the body and its dimensions, making

sure that all wheels are covered by the body when viewed from above.

2.5. Chassis set-up has to be done only within its design limits and only with the

original accessories i.e. changing spring tension or the amount of chassis/body

movement etc.

2.6. All original mounting points and basic configuration must be retained.

2.7. No chassis modifications other then within its design limits.

2.8. No soldering allowed to hold motor into position. Only motor screws are to be

used.

2.9. Body tape or plastic strip may be used to hold lead wires in place.

2.10. Additional weight may be added as long as it is placed on top of the chassis.

2.11. Chassis springs, spacers and/or additional screws and nuts may be substituted,

added or removed.

2.12. Plafit flat body mounts can be used on both chassis in their intended position

either as additional weight or for body mounting.

2.13. No mount plates protruding into wheel arches however minor re-shaping of the

flat body mount plates for proper body fitment is allowed.

2.14. No Traction Magnets.

2.15. Chassis blue-printing is allowed. No excessive sanding for weight reduction !

 

 

3.0 GROUND CLEARANCE

3.1. Minimum 1.0mm under the entire chassis including gear.

 

 

4.0 FRONT AXLE

4.1. Solid 3mm one piece non-independent only.

4.2. Any 3 x 6mm oilite axle bushings or 3 x 6mm axle ball bearings.

 

 

5.0 FRONT WHEELS

5.1. Any 3mm axle diameter aluminium wheels. Minimum diameter including tire is

21.0mm.

5.2. Minimum wheel/tire width is 7mm. No independent front wheels allowed.

5.3. Any black tires, sponge or rubber.

5.4. To retain true-to-scale appearance the wheel diameter is determined by the

individual wheel arch size of the body used.

 

 

6.0 REAR WHEELS

6.1. Any 3mm axle diameter Aluminum Wheels. Minimum diameter including tire is

22.0mm.

6.2. Plafit Black Magic Sponge Tires, Plafit Rubber Tires (labelled) as well as

Scaleauto ProComp3 Sponge Tires are allowed to be used.

6.3. Use of Goo and/or any other tire softener, liquids etc. is not allowed. Cleaning with

Tape or Shellite only is permitted.

6.4. To retain true-to-scale appearance the wheel diameter is determined by the

individual wheel arch size of the body used.

 

 

 

7.0 WHEEL INSERTS

7.1 3D Wheel inserts have to be used at all times.

 

 

8.0 REAR AXLE

8.1. Solid 3mm metal axle only.

8.2. Any 3 x 6mm oilite axle bushings or 3 x 6mm axle ball bearings.

 

 

9.0 GEARS

9.1. Any plastic 50 pitch spur gears for 3mm axles.

 

 

10.0 PINION

10.1. Any 50 pitch.

 

 

11.0 MOTOR

11.1. 13D Plafit 8635 Fox II Motor

11.2. Original lettering "Fox II” has to be visible.

11.3. Sealed Motors are not to be opened or modified in any way.

11.4. Any lead wire.

 

 

12.0 WEIGHT

12.1. Minimum total car weight is 165g.

__________________________________________________________________________________________________________

 

Updated Body List

 

 

 

MZP212 Aston Martin DBR9

MZP419 Audi R8 LMS

MZX25 Chevrolet Corvette C5-R

MZP129R Ferrari F355 Challenge

MZX310 Ferrari 360GTC

MZX321 Ferrari F40

MZX311 Ferrari 575GTC

MZP201 Ferrari Enzo

MZP220 Ferrari Enzo GT Concept

MZP216 Ferrari 599XX

MZP221 Ferrari 458GT2

MXP328 Ferrari F430GT

MZX211 Ferrari FXX

MZX209 Ford GT *

MZP301 Honda NSX 2003

MZX315 Honda NSX 2005

MZP/MSX324 Honda NSX 2007

MZP218 Honda HSV-010

MZG202 Lamborghini Diablo VT

MZP215 Lamborghini Murcielago GT1

MZX319 Lexus SC430

MZP415KM Mazda RX-7 FC

MZX203 McLaren F1 GTR LM

MZP213 McLaren F1 GTR LT

ZK-008 McLaren MP4-12 GT3

MZG305 Nissan 350Z 2004

MZX317 Nissan 350Z 2005

MZP/MSX325 Nissan 350Z 2007

MZG306 Nissan 350Z Hasemi Endless

MZP411 Nissan GT-R

MZP214 Nissan GT-R R35

R246 Nissan R390 GT1

MZP330 Porsche 911 GT1

MZP126 Porsche 911 GT3 RSR

MZX303 Toyota Supra 2003

 

 

* Must have Rear Wing AR-086 or AR90

Edited January 25, 2014 by Camber

[Guest jazzbell]

Platfit Super32 GT Cars

1.0 BODY

1.1. Only 1:32 GT Cars made from hard plastic which are nominated on the Official

Homologation List classified in two divisions are allowed.

1.2. Bodies which feature black no-see-through windows and no driver interior are not

allowed.

1.3. Bodies which feature tinted windows and have a driver interior are allowed.

1.4. Body kits can be used however all kit parts must be assembled. Unpainted kits

have to be painted and must feature a typical Modern GT race livery.

1.5. No major body modifications such as changes to wheel arches or shortening of

under body parts are allowed.

1.6. Original body mounting posts on the body inside can be removed.

1.7. No replacement interiors. Only the original interior the car came with is to be used.

1.8. Existing plastic interiors can be modified just to clear the chassis however the

interior and any other detail has to remain in place to cover all windows.

1.9. Under body front spoilers (fenders) and rear diffusers have to be retained from all

four relevant wheel arches and fitted to the body. This applies especially to body

kits where these parts are not included. Additional plastic chassis plates (original

to the relevant car) are then required to complete the body.

1.10. All original outside detail parts like mirrors and rear wings are to be used at all

times.

 

 

2.0 CHASSIS

2.1. Plafit 3300 Super32 in 3mm or 3/32" chassis versions.

2.2. Chassis has to be adjusted according to the body and its dimensions making sure

that the guide and all wheels are covered by the body when viewed from above.

2.3. All Plafit 3300 chassis system parts can be used.

2.4. Chassis springs, spacers and/or additional screws may be substituted, added or

removed.

2.5. All original mounting points and basic configuration must be retained.

2.6. No chassis modifications other then within its design limits.

2.7. Flat body mount plates can be reshaped to fit both sides of the body.

2.8. ACE Carbon replacement guide holder can be used.

2.9. No soldering permitted to hold motor into position. Only screws are to be used.

2.10. Body tape or plastic strips may be used to hold lead wires in place.

2.11. Additional weight may be added on top of the chassis only.

2.12. Nylon Guide Nuts can be used.

2.13. Plafit 1717A Stabilizer Kit or parts thereof may be used.

2.14. No Traction Magnets.

2.15. Chassis blue-printing is allowed. No excessive sanding for weight reduction !

 

 

3.0 FRONT AXLE

3.1. Any solid 3mm or 3/32" only. No independent front axles/wheels allowed.

3.2. Any 3 x 6mm or 3/32" x 4.75mm oilite axle bushings.

Any 3 x 6mm or 3/32" x 4.75mm axle ball bearings.

 

 

4.0 FRONT WHEELS and TIRES

4.1. Any Plafit 16mm diameter aluminum wheels which comply with the minimum

dimensions may be used.

4.2. Any hard sponge (sealed / non-sealed) tires which comply with the minimum

dimensions may be used.

4.3. Minimum tire diameter is 18.0mm.

4.4. Minimum tire width is 7.0mm.

4.5. 3D Wheel Inserts related in design to the actual car have to be used at all times.

 

 

5.0 REAR WHEELS and TIRES

5.1. Any Plafit 16mm diameter aluminum wheels which comply with the minimum and

maximum dimensions may be used.

5.2. Plafit Black Magic Sponge Tires only. No other brands allowed.

5.3. Minimum wheel/tire diameter with hard rubber and sponge tires is 19.0mm.

5.4. Maximum wheel/tire width with hard rubber and sponge tires is 13.0mm.

5.5. Use of Goo and/or any other tire softener, liquids etc. is not allowed. Cleaning with

Tape or Shellite only is permitted.

5.6. 3D Wheel Inserts related in design to the actual car have to be used at all times.

 

 

6.0 REAR AXLE

6.1. Solid 3mm or 3/32" metal only.

6.2. Any 3 x 6mm or 3/32" x 4.75mm oilite axle bushings.

Any 3 x 6mm or 3/32" x 4.75mm axle ball bearings.

 

 

7.0 GROUND CLEARANCE

7.1. Minimum 1.0mm under the entire chassis including gear for non-magnet racing.

 

 

8.0 WEIGHTS

8.1. Minimum total car weight Division 1 is 125 gr.

8.2. Minimum total car weight Division 2 is 135 gr.

 

 

9.0 GEARS

9.1. Any plastic 50 pitch spur gear.

 

 

10.0 PINION

10.1. Any 50 pitch.

 

 

11.0 MOTOR

11.1. 13D Plafit 8635 Fox II Motor

11.2. Original lettering "Fox II” has to be visible.

11.3. All motors are not to be opened or modified in any way.

11.4. Any lead wire can be used.

 

 

1/32 MODERN GT CARS

 

Official Body Homologation update list for 21014 Plafit Super32 GT Cars

 

CARRERA

 

Maserati MC12 TWO

Aston Martin V12 Vantage GT3 TWO

Audi R8 GT3 TWO

BMW M3 GT2 TWO

BMW Z4 M Coupe TWO

Chevrolet Corvette C6R TWO

Dodge Viper GTS TWO

Ferrari 458 GT2 TWO

Ferrari 575 GTC TWO

Ferrari 599XX TWO

Ferrari Enzo TWO

Mercedes SLR McLaren 722 GT TWO

Mercedes SLS GT3 AMG TWO

Nissan 350Z TWO

Nissan GT-R GT500 TWO

Porsche GT1 Evo TWO

Porsche 997 GT3 RSR TWO

 

FLY + FLYSLOT

 

Saleen S7R GT1 TWO

Corvette C6R TWO

Dodge Viper GTS TWO

Ferrari F40 TWO

Lister Storm TWO

Marcos 600LM TWO

Panoz Esperante GT1 TWO

Porsche GT1 TWO

Sunred SR21 TWO

Venturi 600LM TWO

 

NINCO

 

Mosler MT 900R ONE

Ascari KZ1R TWO

Audi R8 LMS TWO

Callaway Corvette C12R TWO

Chevrolet Camaro GT3 TWO

Corvette GT3 Z06 TWO

Ferrari 360 GTC TWO

Ferrari F50 TWO

Ford GT3 TWO

Ford Mustang GT3 TWO

Honda NSX JGTC TWO

Lamborghini Gallardo GT3 TWO

Lamborghini Murcielago GT1 TWO

Lexus SC430 JGTC TWO

Lotus Exige TWO

McLaren F1 GTR TWO

Mercedes CLK GTR TWO

Mercedes SLS GT3 AMG TWO

Nissan 350Z JGTC TWO

Porsche GT1 TWO

Porsche 911 GT3 TWO

Porsche 997 GT3 TWO

Toyota Supra JGTC TWO

 

NSR

 

Aston Martin DBR9 ONE

Audi R8 LMS ONE

Corvette C6R ONE

Porsche 997 RSR ONE

 

SCALEAUTO

 

Pagani Zonda C12 ONE

Honda HSV-10 ONE

Mercedes SLS GT3 AMG ONE

Spyker C8 ONE

BMW Z4 GT3 ONE

 

SCALEXTRIC

 

Mercedes CLK GTR TWO

Maserati MC12 TWO

Aston Martin DB9R TWO

Audi R8 LMS GT3 TWO

Chevrolet Camaro GT-R TWO

Corvette C6R GT2 TWO

Dodge Viper Competition TWO

Ferrari 360 GTC TWO

Ferrari F40 TWO

Ferrari F430 GT TWO

Ford GT3 TWO

Honda NSX JGTC TWO

Jaguar XJ220 TWO

Jaguar XKRS TWO

Jaguar XKRS GT3 TWO

Lamborghini Diablo VT TWO

Lamborghini Gallardo TWO

Maserati Cambiocorsa TWO

McLaren MP-4 12 TWO

Mercedes SLR McLaren 722 GT TWO

Nissan 350Z JGTC TWO

Nissan Skyline GTR JGTC TWO

Porsche 959 TWO

Porsche GT1 TWO

Porsche GT3 TWO

Toyota Supra JGTC TWO

TVR Tuscan 400R TWO

TVR Speed TWO

 

SCX

 

Ferrari FXX TWO

Aston Martin DB9R TWO

BMW M3 GT2 TWO

Bugatti EB110 TWO

Chevrolet Corvette C6R TWO

Ferrari 360 GTC TWO

Ferrari 599 GTB TWO

Ferrari F40 TWO

Ferrari F550 Maranello TWO

Mercedes SLS GT3 AMG TWO

Porsche 959 TWO

Porsche GT1 TWO

Porsche 911 GT3 TWO

Seat Cupra GT TWO

 

SLOT-IT

 

Porsche GT1 '98 ONE

Nissan R390 GT1 ONE

McLaren F1 GTR LT ONE

Ferrari F40 "Kit" TWO

Edited January 24, 2014 by Camber

[Guest jazzbell]

1/24 Plafit Historic Can-AM HISTORIC CAN-AM and SPORTS CARS NOTE: Concourse will be judged but there will be no points system for results.

 

1.0 BODY

 

1.1. Only 1:24 true-to-scale vacuum formed Lexan Bodies representing historic Can-Am Cars as well as historic Sports Cars and Sports Prototype Cars listed on the 2012 Official Body Homologation List. No other bodies are allowed.

1.2. Minimum body material thickness is .010”.

1.3. Cut out and mounting of body has to reflect the actual 1:1 car.

1.4. The presentation of the body (paint design, decals and additional detail parts) has to be as realistic as possible to a 1:1 car of this time.

1.5. A minimum two piece driver interior (vacuum formed with separate drivers head) to be used. Interior has to cover all windows and open cockpits. No chassis parts are allowed to be visible.

 

 

2.0 CHASSIS

 

2.1. Plafit Excel 1300 or 1300U as well as Plafit Super24 1700C.

2.2. Chassis has to be adjusted according to the body and its dimensions used making sure that all wheels and the guide are covered by the body when viewed from above.

2.3. Maximum polar length (distance back side of rear axle to centre of guide pivot point) is 114mm.

2.4. Chassis set-up has to be done only within its design limits and only with the original accessories i.e. changing spring tension or the amount of chassis/body movement.

2.5. Nuts, screws, springs and washers are free to choose.

2.6. All original mounting points and basic configuration must be retained.

2.7. No further chassis modifications other then within its design limits.

2.8. No soldering allowed to hold motor into position. Only motor screws are to be used.

2.9. Body tape or plastic strip may be used to hold lead wires in place.

2.10. Additional weight may be added as long as it is placed on top of the Chassis and is not protruding outside the chassis edges.

2.11. Chassis blue-printing is allowed. No excessive sanding for weight reduction !

2.12. The Front Chassis Plate Excel 1304C can be shortened only above the two long holes which fit the Front Axle Bracket in order to fit low-front bodies. However both long holes must be retained entirely.

2.13. All 1300 Excel Chassis system parts can be used except 1307C, -CB, -CC, -CD (Flat Body Mount system) and 1314B (front Chassis Weight Plate).

2.14. Only the 1700C Super24 Chassis RTR standard parts can be used which are : 1701J Main Chassis Plate, silver 1703B Guide Holder, long 3309C Bearing Holder +1.0mm, front 1705G T-Plate, blue 1706 Body Mount Plates 1707 Body Slide Mounts 1708 Motor Bracket 1709B Bearing Holder +0.5mm, rear 1710 Subframe 1711 Motor Stay

2.15. Only these additional 1700 Super24 Chassis system parts can be used : 1701 Main Chassis Plate 1703 Guide Holder 1709 Bearing Holder, rear 1709C Bearing Holder +1.0mm 1709D Bearing Holder +1.5mm 1710B Subframe +6mm 1710C Subframe +12mm 1710J Subframe, blue 1710T Subframe with Adjuster 1710BT Subframe +6mm with Adjuster 1710CT Subframe +12mm with Adjuster 1717A Chassis Stabilizer Set Type A

2.16. Flat Body Mounts cannot be used.

 

 

3.0 GROUND CLEARANCE

 

3.1. 1.0mm under the entire chassis including gear.

 

 

4.0 FRONT AXLE

 

4.1. Solid one piece 3mm diameter axles only.

4.2. Any 3mm oilite bushings or ball bearings.

4.3. Maximum front spur width is 79.0mm but never wider then the body used.

 

 

5.0 FRONT WHEELS / TIRES

 

5.1. Any Plafit 17mm diameter Alu Wheels. Minimum tire diameter is 22mm

5.2. Any Hard Sponge Tires non-sealed.

5.3. Minimum tire width is 7mm. No independent front wheels allowed.

 

 

6.0 REAR WHEELS / TIRES

 

6.1. Any Plafit 17mm diameter Alu Wheels. Minimum tire diameter is 24mm.

6.2. Plafit BM Sponge Tires only, maximum tire width is 16mm.

6.3. Use of Goo and/or any other tire softener, liquids etc. is not allowed. Cleaning with Tape or Shellite only is permitted.

 

 

7.0 WHEEL INSERTS

 

7.1. 3D Wheel Inserts have to be used on all wheels at all times.

 

 

8.0 REAR AXLE

 

8.1. Solid metal 3mm axles only.

8.2. Any 3mm oilite bushings or ball bearings.

8.3. Maximum rear spur width is 79.0mm but never wider then the body used.

 

 

9.0 GEARS

 

9.1. Any plastic 50 pitch spur gears for 3mm axles.

 

 

10.0 PINION

 

10.1. Any 50 pitch 10 T only.

 

 

11.0 MOTOR

 

11.1. Only 13D Plafit Fox II Motor.

11.2. Original lettering “PLAFIT FOX II China” has to be visible.

11.3. Sealed Motors are not to be opened or modified in any way.

11.4. Any lead wire.

 

 

BODY HOMOLOGATION LIST

Historic CAN-AM and SPORTS CARS

1. January 2014

 

SUNSET RACING SHELLS (AUS)

(Lexan)

- 1967 Chaparral 2F *

- 1967 Chaparral 2G *

- 1966 Elfin T400

- 1966 Ford GT40 MKII

- 1967 Ford GT40 MKIII

- 1969 Ford GT40 Mirage

- 1968 Ford 3L

- 1962 Honker II

- 1964 King Cobra

- 1965 Lotus 40

- 1968 Marcos Mantis

- 1966 McLaren MKII

- 1967 McLaren M6A

- 1968 McLaren M8A

 

ACE BODIES (AUS)

(Lexan)

- 24300 1969 Porsche 917LT

- 24301 1970 Porsche 917K

- 243011 1970 Porsche 917K (old)

- 24400 1966 Elfin T400

- 24817 1968 Marcos Mantis

- 24812 1970 Ferrari 512M

- 24813 1970 Ferrari 312PB

- 24815 1970 Chevron B19

- 24807 1969 Lola T163

- 24817 1967 Lola T162

- 24816 1966 Lola T70 Spyder

- 24409 1968 McLaren M8A

- 24412 1970 Chaparral 2J

- 24818 1968 Ford 3L

 

LANCER BODIES (USA)

(Lexan)

- 146 1966 Ford J

- 156 1967 Ford GT40 MK4

- 153 1968 Lola T-70 MKIII GT

- 157 1969 Ford GT40 Mirage

- 163 1967 Ferrari 350P4 CanAm

 

VINTAGE BODIES (USA)

(Lexan)

- 24-47 1966 Lola T-70 Roadster

- 24-51 1966 Ford GT40

- 24-61 1968 Lola T-70 MKIII GT

 

* These bodies can only be used with a high-set wing as they have never raced without

Edited January 24, 2014 by Camber

[Guest jazzbell]

LMP/GT1 PROTO Open Rules:

 

NOTE :EVEN THOUGH IT IS AN OPEN CLASS THE CAR MUST STILL LOOK LIKE A RTR 1/32 SCALE CAR .

 

AXLES FRONT(Total width of wheels must not exceed the original set up)

1.Must be located in original,un-modified front axel holders.

2.Stabelizing of front end is allowed.

 

AXLES REAR(Total width of wheels and axle must not exceed the original set up)

1.Must be located in original un-modified rear axel holders.

2.Ball bearings are allowed.

 

BODY:

1.NO sanding of wheel arches to allow for room for tyres to fit.

2.The body can NOT be modified in any way.Exception on the Nissan R90 where the gear hits on the air duct

3.Any screws can be used.

4.Any body that has a wing can have rubber added as struts to stop the wing from braking off.

5.Painted liveries are allowed making sure all parts are used. Race numbers in at least 3 places.

 

CHASSIS:

1.Adding weight to any part of the chassis is allowed.

2.Reinforcing or gluing parts of the chassis such as axel bushings,motor mounting posts etc is allowed.

3. NO chassis magnets are allowed.

4. Must be plastic RTR chassis that comes with car. No metal chassis.

 

GEARS:

1. OPEN Gear Ratio.

 

GROUND CLEARANCE:

1. As long as day light can be seen.

 

GUIDE:

1.Any Guide.

2.Any lead wire.

3.Any Braid.

 

Interior:

1. Lexen can be used.

 

MOTOR:

1. Long or Short can motors up to 30,000 RPM

 

TYRES:

1. FOAM TYRES ONLY.

NSR,SCALEAUTO OR SLOT.IT

 

 

NO Tyre softening, conditioning or treating is allowed.

Tyres cleaning with Shellite only.

 

Some of the cars eligible for this class.

 

AVANT SLOT:

Peugeot 908

Porsche Spyder

Audi

Pescarolo LMP

 

SLOTINGPLUS:

Raynard 2KQ

 

SCALEAUTO:

RadicalSR-9

Toyota GT-1

 

SLOT.IT:

Nissan R390 GT1

LOLA BO9/60S

Audi R8C

McLaren GTR

 

NINCO:

Acura.

Audi R8

 

SCX:

Audi R8

Audi R10

 

NSR:

Audi R18

Audi R8

 

Scalextric:

Porsche spyder

Peugeot

Lola Aston Martin 1-2

Audi R8

____________________________________________________________________________________________________

 

 

 

 

[Guest jazzbell]

SCX NASCARS

 

AXLES FRONT: (Front width of wheels can protrude .5 of a mm outside the guard either side of original set up)

1. Original front axle.

2. Must be located in the original, unmodified front axle holders.

3. Side play may be adjusted by adding axle washers.

 

AXLES REAR: (Rear width of wheels can protrude .5 of a mm outside the guard either side of original set up)

1. Original rear axle and bushings only. No ball bearings.

2. Must be located in the original, unmodified rear axle holders.

3. Side play may be adjusted by adding axle washers.

4. Note some rear ends stick out past the guards when cars are purchased,this is allowed as long as its no more than 1mm either side.

 

BODY:

1. Only original unmodified SCX NASCAR style bodies are allowed.The exception on removing the bearing holder supports that come down from the body front and rear.

2. Rear wings and mirrors must be mounted on the body in the original position before the start of the race.

3. If the rear wing becomes detached during the race, in must be re-attached before the start of the next bracket.

4. Mirrors, aerials, chipped or lost wing pieces don’t have to be re-attached during the race.

5. The windows must remain as original and in place at all times.

6. The body must not be altered in any way, and must be at least 0.5mm clear of the track surface.

7. Only very minor sanding is allowed to allow body rock.

8. All the body screws must be in place. Any screws may be used. The screws may be left loose.

 

CHASSIS:

1. Only the original unmodified SCX Classic chassis is allowed.

2. The chassis and body must be from the original car as first purchased.

3. Adding weight to any part of the chassis is allowed.

4. Reinforcing or gluing parts of the chassis such as axle bushings, motor mounting posts is allowed.

5. NO MAGNETS ALLOWED.

6.SCX Pro nascar's are banned. SCX cot or aero cars only.

 

GEARS:

1. Original drive gear.

2. Original pinion gear.

2. Only a 9 tooth pinion is allowed.

 

GROUND CLEARANCE:

1. Minimum .5mm clearance under the entire chassis and body at all times.

2. Any tyre changes or repairs must pass another Tech Check before the car can re-enter the race.

 

GUIDE:

1. SCX guide ONLY.

2. Any lead wire.

3.Any braid.

4.Hot Glue or Gluing guide up to have good power connection is allowed.

 

INTERIOR:

1. Original unmodified interiors must be in place at all times.

 

MOTOR:

1. ONLY the RX-42B 19000 RPM SCX motor, SUSPECT MOTORS WILL BE CHECKED.

2. If the motor came with a motor wrapper type label, it must not be tampered with or modified in any way. (i.e. no venting)

3. The motor may be secured by soldering a motor brace or gluing it to the chassis without disturbing the motor wrapper.

4. The crimped motor can tabs holding the end bell must not be tampered with, otherwise it will be disqualified.

5.The copper links between the motor and guide maybe soldered to avoid any chance of loosing

a good connection.

6.soldering of lead wire from motor tabs to rails is allowed.

7.motor cradle can be glued or taped.

8.Resistors can be removed.

 

WHEELS FRONT: (No silicon tyres!)

1. Only original SCX tyres or MJK’s are permitted.

2. Sanding / truing front tyres is permitted.

3. Tyres must touch the track surface when placed on the track.

4. Original rims only.

 

WHEELS REAR: (No silicon tyres!)

1. Only original SCX tyres or MJK’s-4230's(20.5x9.8) are permitted.

2. Sanding / truing tyres is OK.

3. TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED. Tyre shore hardness may be checked against original packet standard tyres.

4. Original rims only.

 

[Guest jazzbell]

SCALEXTRIC GT MAGNET RULES (AMATEUR ONLY)

 

THIS IS A MAGNET RACED CLASS. MAXIMUM DOWNFORCE READING ON THE MAGNET MARSHALL WILL BE 350.

NOTE YOU CAN ONLY RUN 1 MAGNET,BUT CHANGING OF MAGNET IS ALLOWED AS LONG AS IT FITS IN ORIGIANAL

POSITION AND DOSNT EXCEED 350 DOWNFORCE.

 

NO HIGH IMPACT CARS ALLOWED IN THIS CLASS.

 

AXLES FRONT.(Front wheels can exceed.5 of a mm out side the guard on either side of original set up)

1. Original front Axel set up.

2.Must be located in original,unmodified front axle holders.

3.Side play may be adjusted by adding axle spacers.

 

AXLES REAR.(Rear wheels can exceed .5 of a mm out side the guard on either side of original set up.)

1.Original rear axle and bushings only.NO BALL BEARINGS.

2.Must be located in the original ,unmodified rear axle holder.

3.Side play may adjusted by adding washers.

 

Body.

1.Original unmodified Scalextric GT style bodies are allowed.

2.Rear wings must be mounted in original position before the start of a race.They also can be mounted with rubber supports to help prevent wings breaking off.Must remain in original position.

3.The windows must remain original and clear at all times.

4.The body must not be altered in any way and must have a .5mm ground clearance of the track surface.

5.Any screws may be used.Screws may be left loose.

6.Light shave of body is allowed to stop body catching on chassis.

7.Posts can be sleeved for more support and strenght to prevent breakages .

8.Painted liveries are allowed as long as all parts are used and 3 numbers are in place on the car.

 

Chassis.

1.Only the original unmodified Scalextric GT style chassis is allowed.

2.Adding weight to any part of the chassis is allowed.

3.Gluing of bearings and gluing motor in is allowed.

4. Slight shave of the chassis is allowed to top from catching on the body.

5.Post holes can be opened up to stop screws catching.

 

Gears.

1.Original plastic drive gear.

2.Original drive gear.

 

Ground Clearance.

1. 0.5mm clearance under hole chassis.

 

Guide.

1.Original guide.

2.Any lead wire.

3.Any braid.

 

Interior.

1.Original unmodified interiors in place at all times.

 

Motor.

1.Original Scalextric 18,000 rpm motors only.

2.The sealed motors can not be tampered with in any way.

3.Motors can be glued or taped in.

4.Resistors can be removed.

5.Lights can be removed or disconnected.

 

Wheels/Tyres FRONT.

1.Original Scalextric only.Truing and gluing is allowed.

2.The front wheels must touch the flat surface when placed on the set up board.

3.Original rims only.

 

Wheels/Tyres REAR.

1.Original Scalextric tyres and the only replacement is MJK. Gluing and truing is allowed.

2.Original rims only.

3.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED. Tyre shore hardness may be checked against original packet standard tyres.

__________________________________________________________________________________________________________

 

[Guest jazzbell]

NINCO GT RULES AXLES FRONT:

(Front wheels can protrude .5 off a mm outside the guard either side of original set up) 1. Ninco front axle.

2. Must be located in the original, unmodified front axle holders.

3. Side play may be adjusted by adding axle washers.

 

AXLES REAR:

(Total width of wheels and axle must not exceed the original set up if using the pro race wheels.Using original plastic wheel rear end the total rear width can protrude .5 of a mm outside the guard either side.)

1. Ninco pro race rear ends are allowed.(3/32 or 2.45mm)

2. Must be located in the original, unmodified rear axle holders.

3. Side play may be adjusted by adding axle washers.

 

BODY:

1. Only original unmodified Ninco GT style bodies are allowed.

2. Rear wings and mirrors must be mounted on the body in the original position before the start of the race.They can be fitted with rubber supports to prevent breakages.Must remain in original position.

3. If the rear wing becomes detached during the race, in must be re-attached before the start of the next bracket.

4. Mirrors, aerials, chipped or lost wing pieces don't have to be re-attached during the race.

5. The original windows must remain clear and in place at all times.Also the dark windows in the lightning car range is ok.

6. The body must not be altered in any way, and must be at least 0.5mm clear of the track surface.

7. NO sanding is allowed inside wheel arches to stop the tyres from rubbing.

8. All the body screws must be in place. Any screws may be used. The screws may be left loose.

9.Painted liveries are allowed making sure all parts are used.Race numbers must be in at least 3 places.

 

Some of the cars eligible for this class:

(please note: Pro-Race cars are allowed)

50444 Ascari KZ1R

50307 BMW M3 GTR

50255 Callaway Corvette C12R

50123 Ferrari F50

50355 Honda NSX-GTR

50129 McLaren F1 GTR

50413 Mosler MT 900R

50417 Nissan 350Z JGTC

50241 Porsche 911 GT3

50149 Porsche GT1 50369

Toyota Supra JGTC

More cars to be added as they come to hand ...

 

CHASSIS:

1. Only the original unmodified Ninco GT style chassis is allowed.

2. The chassis and body must be from the original car as first purchased.

3. Adding weight to any part of the chassis is allowed.

4. Reinforcing or gluing parts of the chassis such as axle bushings, motor mounting posts etc is allowed.

5. NO chassis magnets are allowed.

6. Bracing rear ends is allowed

7.The new pod chassis can be used

 

GEARS:

1. Original plastic drive gear.

2. Original plastic pinion gear.

3. The Ninco pro race range is allowed also. This is introduced for the first time due to the range of lightning cars that are available.

4. Gear ratio is 12/32.

A. 3/32 is the black gear,part number 80232 or 80246.

B. 2.45mm is a silver gear,part number 80215.

NOTE: Counting the teeth on pinion to make sure a 12 is being used will happen.

 

GROUND CLEARANCE:

1. Minimum 0.5mm clearance under the entire chassis and body at all times.

2. Any tyre changes or repairs must pass another Tech Check before the car can re-enter the race.

 

GUIDE:

1. Any Ninco guide.

2. Any lead wire.

3. Any lead wire.

 

INTERIOR:

1. Original unmodified interiors must be in place at all times.

2. Ninco Lexan is allowed.

 

MOTOR:

1. Original unmodified Ninco NC-5 MOTORS only.

2. The seal (motor wrapper) must not be tampered with or modified in any way. (i.e. no venting)

3. The motor may be secured by soldering a motor brace or gluing it to the chassis without disturbing the motor wrapper.Motors may be taped in.

4. The original resistor can be removed.

5. The motor casing/endbell must not be tampered with in anyway.

 

WHEELS FRONT: (No silicon tyres!)

1. Original Ninco tyres only. Sanding / truing front tyres is OK.

2. Tyres must touch the track surface when placed on the track.

3. Original rims.

4. Ninco Prorace rims are allowed. 3/32 AND 2.45MM.

 

WHEELS REAR: (No silicon tyres!)

1. FOAM TYRES ONLY SLOTIT/NSR PART NUMBERS 9024 AND 9025/SCALEAUTO SC-2009P

2. TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED.

3. Ninco prorace rims are allowed. 3/32 and 2.45mm.

Edited January 24, 2014 by jazzbell

[Guest jazzbell]

SLOT IT GROUP C RULES.

AXLE FRONT:(Total width of wheels and axle must not exceed the original set up.)

1. Original front axle.

2. Must be located in the original,unmodified front axle holders.

3. Side play may be adjusted by adding axle washers.

 

AXLE REAR:(Total width of wheels and axle must not exceed the original set up.)

1.Original rear axle bushings only,NO ball bearings.

2. Must be located in original,unmodified rear axle holders.

3. Side play may be adjusted by adding axle washers.

 

BODY:

1.Only the original unmodified Slot.It group C in-line chassis is allowed.

2.Rear wings must be mounted on the body in the original position before the start of the race.Rubber supports can be added to prevent wings from breaking off.Must be in original position.

3.If the rear wing comes detached during the race,it must be re attached before the next bracket.

4.The windows must remain original and in place at all times.

5.The body must not be altered in any way.

6. All the body screws must be in place.Any screws may be used.

7. The rear spats can be removed on the XJ9 and XJ12 Jaguar.

8. Painted liveries are allowed making sure all the parts are used and numbers have to be in at least 3 places on the car.

 

Legal bodies.......

Mercedes Sauber C9

Mazda 787 B Lancia LC 2

jaguar XJ9 and XJ12

Porsche 956 KH

Porsche 962 C

Porsche 956 C

Toyota 88 C

 

CHASSIS:

1.Only the original unmodified Slot.It group C chassis is allowed.

2. Adding weight to any part of the chassis is allowed.

3. Reinforcing or gluing parts of the chassis such as axle bushings,motor mounting post is allowed.

 

4. NO MAGNETS.

 

GEARS:

1.Original Slot.It YELLOW 28T crown in-line gear.

2.Original Slot.It 9T pinion.

 

GROUND CLEARANCE:

1. Day light must be seen.

 

GUIDE:

1.Any Slot.It replacement guide.

2.Any lead wire.

3.Any braid.

 

INTERIOR:

1.Original unmodified interiors must be in place at all times.

 

MOTOR:

1.Original unmodified 21,500rpm slot.it group C motors only.

2.The motor tabs holding the end bell must not be tampered with in any way,otherwise it will be disqualified.

3.Cars that came with the 25,000rpm motor can change them to a 21,500rpm motor.

 

WHEELS/TYRES FRONT:(NO SILICON TYRES.)

1.Only original slot.it group C tyres are permitted.

2.Sanding gluing and truing is allowed.

3.Tyres must touch on set up board when checked.

4.Original rims only.

 

WHEELS/TYRES REAR:(NO SILICONS TYRES.)

1.FOAM TYRES ONLY. SLOT IT/NSR PART NUMBERS 9024 AND 9025/SCALEAUTO SC-2009P

2.Sanding gluing and truing is allowed.

3.original rims only.

4.TYRE TREATING, CONDITIONING OR SOFTENING IS NOT ALLOWED.

 

 

[Guest jazzbell]

NSR CLASSIC

 

AXLES FRONT:(Total width of wheels and axle must not exceed the original set up)

1.Original front axle.

2.Must be located in original,un-modified front axle holders.

3.Side play may be adjusted by adding axle washers.

 

AXLES REAR:(Total width of wheels and axle must not exceed the original set up.)

1.Original rear axle bushings only.

2.Must be located in the original,un-modified rear axle holders.

3.NO BALL BEARINGS.

 

BODY:

1.NSR Classic body only.

2.Painted liveries are allowed.Numbers have to be in at least places on the body.

3.Srew posts can be sleeved for extra support to prevent breakages.

4.If the car comes with the dummy spare wheel it must remain in the car as it come.

 

CHASSIS:

1.Only the NSR classic chassis for the make of car be used(Porsche to Porsche etc.)

2.Adding weight to any part of the chassis is allowed.

3.Reinforcing or gluing parts of the chassis such as axle bushings,motor mounting posts ect is allowed.

4.No chassis magnets are allowed.

 

GEARS:

1.NSR GEARS ONLY.Gear ratio is 11/32.

 

GROUND CLEARANCE:

1.Day light must be seen.

 

GUIDE:

1.Any wood track guide.

 

INTERIOR:

1.Original un-modified interiors must be in place at all times.

 

MOTOR:

1.Un modified small can shark 20,000rpm motors only(comes standard in all nsr classic cars).

2.Side winder set up only.

3.The motor may be glued or taped in.

4.The motor tabs must remain intac,any tampering will result in diqualification.

5.Motor lables must be intact.Orange 20,000rpm.

 

WHEELS/TYRES FRONT:(NO Silicon)

1.Any front tyre.

2.Sanding/truing tyre is permitted.

3.tyres must touch the track surface.(allowance will be made as these cars released the fronts do not always touch the set up board.)

4.Original rims only.

 

WHEELS/TYRES REAR: (NO Silicon)

1.FOAM TYRES ONLY....NSR PART NUMBERS 9024 AND 9025/SLOT IT/SCALEAUTO SC-2009P

2.Sanding/Gluing and truing is allowed.

3.TYRE TREATING, SOFTENING OR CONDITION OF ANY KIND IS NOT ALLOWED.

4.Cleaning with shellite ONLY is allowed.

[jimmyslots 1950 25]