Jump to content

Pauls Slots

Members
  • Content Count

    339
  • Joined

  • Last visited

  • Days Won

    1

Everything posted by Pauls Slots

  1. Gday Nimrod, Ben watching the progress with you Blue Bird. Nice work. Any chance to order one please. regards, Paul
  2. Nice work Terry, All set up for next year? , we all better get our fingers out and get started. Paul
  3. Nice work mate. Nice car to drive also.
  4. Thanks Phil. As you know just happens some times. All the planets align, and a little pixie dust ps; will be chasing you for a shell for next year. Thanks again, Paul
  5. Alan, thanks for putting on the series. Lots of work and effort behind the scenes for you and the missus.. Well done to all entrants for building these great little cars. All the track owners, drivers and marshals who help and run the events. Could not be done without you lot. In all I am surprised at how well my little car went. Was a quick build over many months. When time would allow. All my past cars were OK, but not good enough. Something to put into next years race. Well done to Alan and Brumos Both racers we held in Adelaide were hard fought and conditions on the day played a major part in the results. Thanks again, Paul
  6. Hi all, Today is the day. Racing at 1300, at Spitfire Raceway (due to Covid, invites only) Good luck to you all. See you at what is the end of this series for this year.
  7. Hi all, Alan has put out the feelers and looks to be a race schedualed for this Saturday afternoon 31st . LOOK OUT and STAND BACK If she comes off all the best to all.
  8. Extremely well done . Has any one actually raced one. How o they go. Can only imagine the cost would be expensive. Paul
  9. Well done Alan, Good luck to all involved. Hope the little cars get to the end in one piece. See you all at the end.
  10. Hi all, Well done Brumos and Lenny. Thanks to drivers and marshals. Must have been an exiting run with the little cars. Most seem to be with a lap or so for most of the race. Big race day . Well done all and thanks again. Paul
  11. Thanks Terry, Nice work Paul. Congratulations big Al. Paul
  12. Hi Phil and Peter. Seems most of the cars and times are similar paced. Looks as if a crash or fall off is the difference between most. Good luck to all Paul
  13. Hi all, What a surprise , did not know round three was to be completed. Looks like the 1512 Ferrari is going well. Hope to see drivers notes for this and the last round come up at some point. Thanks to all involved.
  14. Hi all, Thanks to Alan and Mike, all the drivers and marshals. Alan great effort to get this series off the ground this year. Mike thank you for hosting a great day. All the drivers did extremely well as did all the cars. Most of the races / cars were consistent with little off's and not much carnage, at all. Marshaling was not to busy at all. The track is technical and requires concentration. It is a great track for these little cars. Most of all when I built the little 1512 Ferrari I did not expect to place on the podium never mind wining the round. Congratulations the Dennis and Brumos. See where we end up by the end of the series. Best of luck to all Thanks again Paul
  15. Nice work Alan. Look forward to testing and the race at Mikes. Paul
  16. Hi Alan, My Ferrari is nearly there. Had a quick run around at Marks. Final detail and decals, shes done. Then a tune up run. Specs; Ferrari 1512 PP shell PP chasis SRP18 9/24 ratio PP wire spoke rims MJK tyre Solt it guide
  17. Nice work Rosco. Looking forward to getting mine. Paul
  18. Hi all. MEK is also used in manufacture of fiberglass and similar products (shipwrights and glassies use it every day) You maybe able to pick up from local chandler shop NOTE; this product is extremely dangerous if misused. DO NOT get i you eyes. This will make you go blind in minutes if not treated. We had a guy at work (we saved) and his screams I will never forget. Be careful lads.
  19. Rosco thanks for the reply. Seems if you want to build a chassis you need this. I have tried to drill off an Ally plate 10mm thick. Is not close enough when you get down to scale. Thanks again, Will chase him up. Paul
  20. Hi Rosco, Nice work mate. Nice to see how the Torry goes. Rosco I have been looking for a build plate for a while. Can I ask where did you get the Precision Slot build plate from. Thanks, Paul
  21. Thanks Den, Yes they are expensive. I picked up one of the Chrono kits. Needs full assembly. Thought it was worth a look. As you say the front tend is a bit light on. Have seen on here at some time a retro fit front clip/ chassis. this converts to a solid axle. If I could get one of these modification kits it may be a good thing. Cheers, Paul
  22. Hi all. Have purchased a Chrono SRC M23 (kit) Looking to set up as track car. Has any one done this as yet. Looking to see if there are issues with the front axle and or steering. I would think an axle may be better, than the steering system that is supplied with the car.. Also though some one was producing a chassis to accept an axle set up. See like a fairly well detailed kit with every thing. Thanks, Paul
  23. Will have a look on the weekend Johnny Let you now.
  24. Need to get a move on. It will be time before we know it. Good luck lads an girls (as the case may be)
×
×
  • Create New...